- 您现在的位置：买卖IC网 > PDF目录44997 > LTC4412IHVS6#TRM (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 PDF资料下载
参数资料
| 型号： | LTC4412IHVS6#TRM |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封装： | PLASTIC, MO-193, TSOT-23, 6 PIN |
| 文件页数： | 2/12页 |
| 文件大小： | 176K |
| 代理商： | LTC4412IHVS6#TRM |
10
LTC4412HV
4412hvf
TYPICAL APPLICATIO S
U
rising. This is due to the SENSE pin voltage rising above
the battery voltage and turning off the MOSFET before the
Schottky diode turns on. The factors that determine the
magnitude of the voltage droop are the auxiliary input rise
time, the type of diode used, the value of COUT and the load
current.
Ideal Diode Control with a Microcontroller
Figure 4 illustrates an application circuit for microcontrol-
ler monitoring and control of two power sources. The
microcontroller’s analog inputs, perhaps with the aid of a
resistor voltage divider, monitors each supply input and
commands the LTC4412HV through the CTL input. Back-
to-back MOSFETs are used so that the drain-source diode
will not power the load when the MOSFET is turned off (dual
MOSFETs in one package are commercially available).
With a logical low input on the CTL pin, the primary input
supplies power to the load regardless of the auxiliary
voltage. When CTL is switched high, the auxiliary input
will power the load whether or not it is higher or lower
than the primary power voltage. Once the auxiliary is on,
the primary power can be removed and the auxiliary will
continue to power the load. Only when the primary
voltage is higher than the auxiliary voltage will taking CTL
low switch back to the primary power, otherwise the
auxiliary stays connected. When the primary power is
disconnected and VIN falls below VLOAD, it will turn on the
auxiliary MOSFET if CTL is low, but VLOAD must stay up
long enough for the MOSFET to turn on. At a minimum,
COUT capacitance must be sized to hold up VLOAD until the
transistion between the sets of MOSFETs is complete.
Sufficient capacitance on the load and low or no capaci-
tance on VIN will help ensure this. If desired, this can be
avoided by use of a capacitor on VIN to ensure that VIN
falls more slowly than VLOAD.
Load Sharing
Figure 5 illustrates an application circuit for dual battery
load sharing with automatic switchover of load from
batteries to wall adapter. Whichever battery can supply the
higher voltage will provide the load current until it is
discharged to the voltage of the other battery. The load will
then be shared between the two batteries according to the
capacity of each battery. The higher capacity battery will
provide proportionally higher current to the load. When a
wall adapter input is applied, both MOSFETs will turn off
and no load current will be drawn from the batteries. The
STAT pins provide information as to which input is supply-
ing the load current. This concept can be expanded to
more power inputs.
VIN
GND
CTL
SENSE
GATE
STAT
1
2
3
6
5
4
LTC4412HV
COUT
TO LOAD
STATUS IS HIGH
WHEN BAT1 IS
SUPPLYING
LOAD CURRENT
WHEN BOTH STATUS LINES ARE
HIGH, THEN BOTH BATTERIES ARE
SUPPLYING LOAD CURRENTS. WHEN
BOTH STATUS LINES ARE LOW THEN
WALL ADAPTER IS PRESENT
STATUS IS HIGH
WHEN BAT2 IS
SUPPLYING
LOAD CURRENT
470k
4412HV F05
VCC
BAT1
WALL
ADAPTER
INPUT
VIN
GND
CTL
SENSE
GATE
STAT
1
2
3
6
5
4
LTC4412HV
470k
VCC
BAT2
*
*DRAIN-SOURCE DIODE OF MOSFET
Figure 5. Dual Battery Load Sharing with Automatic
Switchover of Load from Batteries to Wall Adapter
VIN
GND
CTL
SENSE
GATE
STAT
1
2
3
6
5
4
LTC4412HV
*DRAIN-SOURCE DIODE OF MOSFET
PRIMARY
P-CHANNEL MOSFETS
COUT
TO LOAD
4412HV F04
AUXILIARY POWER
SOURCE INPUT
*
PRIMARY
POWER
SOURCE INPUT
AUXILIARY
P-CHANNEL MOSFETS
470k
MICROCONTROLLER
0.1
F
Figure 4. Microcontroller Monitoring and Control
of Two Power Sources
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4412IHVS6#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4412IHVS6#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4413EDD-2 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LTC4413EDD-1#TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LTC4413EDD2#TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4412IS6#PBF | 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:IC POWERPATH CONTROLLER SOT-23-6 制造商:Linear Technology 功能描述:IC, POWERPATH CONTROLLER, SOT-23-6 制造商:Linear Technology 功能描述:IC, POWERPATH CONTROLLER, SOT-23-6; Input Voltage:28V; Output Current:50A; Output Voltage:36V; Supply Voltage Min:2.5V; Supply Voltage Max:28V; No. of Pins:6; No. of Outputs:1; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| LTC4412IS6#TRMPBF | 功能描述:IC PWR PATH CNTRLR TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4412IS6#TRPBF | 功能描述:IC CTRL LOWLOSS PWRPATH TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4412IS6TRMPBF | 制造商:Linear Technology 功能描述:PowerPath Controller Low-Loss TSOT23-6 |
| LTC4413EDD | 制造商:Linear Technology 功能描述:Dual Ideal Diodes 10-Pin DFN EP |
发布紧急采购，3分钟左右您将得到回复。