参数资料
| 型号： | LTC4415EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC DUAL 4A DIODES 16-MSOP |
| 标准包装： | 37 |
| 系列： | PowerPath™ |
| 应用： | 备用电池，高电流开关 |
| FET 型： | P 沟道 |
| 输出数： | 2 |
| 内部开关： | 是 |
| 电源电压： | 1.7 V ~ 5.5 V |
| 电流 - 电源： | 44µA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 16-MSOP |
| 包装： | 管件 |
LTC4415
OPERATION
I OUT = 1000 ?
TO GND
THERMAL
SHUTDOWN
10ms/DIV
V IN = 3.6V
whentheloadcurrentdecreasesbelowthecurrentlimit.
Power consumption in LTC4415 increases during opera-
tion in current limit due to the large voltage drop across
the PFET devices (P1 or P2).
Load Current Monitor
The current limit pins output 1/1000th of the ideal diode
output current. The voltage across the current limit resis-
tor can be measured to monitor the current through each
ideal diode as follows:
V CLIM
R CLIM
Note that the current monitor function via V CLIM is not
available when CLIM pins are grounded to use the fixed
internal current limit.
Soft-Start
An internal soft-start is included for each ideal diode to
minimize the start-up inrush current. When either of the
diodes start forward conduction, the load current ramps
from zero to the set current limit over a period of 2ms. The
soft-start can be monitored by observing the CLIM1 and
CLIM2 pin voltages when they are connected to grounded
resistors. Soft-start duration is reduced to 0.5ms (typical)
when the CLIM pins are grounded. In order to minimize
output droop during switchover between input sources
in power supply ORing applications, soft-start is disabled
when the output voltage is above 1.2V.
Forward Conduction Status Monitor
Active low open-drain output status signals, STAT1 and
STAT2 , indicate the forward conduction status of each
ideal diode. With resistor pull-ups on these status pins,
a low voltage indicates forward conduction from input to
output, IN1/IN2 to OUT1/OUT2, respectively. The status
pins go to high impedance when the respective ideal diodes
are disabled, during reverse turn-off conditions, or during
thermal shutdown.
Thermal Warning and Shutdown
Thermal sensors within the LTC4415 monitor the die tem-
perature when either of the diodes are enabled. When the
die temperature exceeds the warning threshold (130°C),
the WARN1 / WARN2 pins are pulled down with open-drain
NFETs while the LTC4415 continues to operate normally.
This gives some time for the user to reduce the load current
to avoid thermal shutdown. The warning signal is deas-
serted when the die temperature cools down below 115°C.
Thermal shutdown is triggered when the internal die
temperature increases beyond the fault threshold (160°C).
Status pins, STAT1 / STAT2 , are deasserted during thermal
shutdown to indicate the interruption in forward condi-
tion. Normal operation resumes when the die temperature
cools below 140°C. Note that prolonged operation at the
overtemperature condition degrades device reliability.
Figure 2 shows WARN followed by thermal shutdown
caused by an output short-circuit to ground. Time to
thermal shutdown varies depending on power dissipation,
ambient temperature and board layout. The output cur-
rent ramps up after the device cools down below 140°C,
but shuts down repeatedly as the device overheats due
to persistent short.
V OUT OUTPUT SHORTED
2V/DIV
I OUT
2A/DIV
RESTART DUE TO
THERMAL HYSTERESIS
STAT
5V/DIV
WARN
5V/DIV
4415 F02
R CLIM = 124
C OUT = 4.7μF
Figure 2. Current Limit Warning and
Thermal Shutdown on Output Short Circuit
The thermal sensors are independent for each diode to
warn of, or shut down the heat generating path so that it
does not hinder the normal operation of the other path.
Depending on the amount of heat generated, the whole
die may still heat up and eventually shut down the other
channel.
4415fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4416EMS#PBF | IC CTLR POWERPATH 10-MSOP |
| LTC5100EUF#TRPBF | IC DRIVER VCSEL 3.2GBPS 16QFN |
| LTC660CS8#TRPBF | IC REG DBL INV ADJ 0.1A 8SOIC |
| LTC6801HG#TRPBF | IC BATTERY MON MULTICELL 36SSOP |
| LTC6802IG-1#TRPBF | IC MONITOR BATT STACK MC 44-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4415IDHC#PBF | 功能描述:IC DUAL 4A DIODES 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415IDHC#TRPBF | 功能描述:IC DUAL 4A DIODES 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415IMSE#PBF | 功能描述:IC DUAL 4A DIODES 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415IMSE#TRPBF | 功能描述:IC DUAL 4A DIODES 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4416EMS | 制造商:Linear Technology 功能描述:OR Controller P-Channel Dual-OUT 10-Pin MSOP |
发布紧急采购，3分钟左右您将得到回复。