- 您现在的位置：买卖IC网 > PDF目录67759 > LTC6405IMS8E#TRPBF (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO8 PDF资料下载
参数资料
| 型号： | LTC6405IMS8E#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封装： | LEAD FREE, MSOP-8 |
| 文件页数： | 3/24页 |
| 文件大小： | 281K |
| 代理商： | LTC6405IMS8E#TRPBF |
LTC6405
11
6405fa
PIN FUNCTIONS
VOCM (Pin 2/Pin 4): Output Common Mode Reference
Voltage. The voltage on VOCM sets the output common
mode voltage level (which is dened as the average of the
voltages on the +OUT and –OUT pins). The VOCM voltage
is internally set by a resistive divider between the supplies,
developing a default voltage potential of 2.5V with a 5V
supply. The VOCM pin can be over-driven by an external
voltage capable of driving the 19kΩ Thevenin equivalent
impedance presented by the pin. The VOCM pin should be
bypassed with a high quality ceramic bypass capacitor of at
least 0.01μF, to minimize common mode noise from being
converted to differential noise by impedance mismatches
both externally and internally to the IC.
V+ (Pin 3/Pins 2, 10, 11):
V– (Pin 6/Pins 3, 9, 12):
Power Supply Pins. It is critical that close attention be
paid to supply bypassing. For single supply applications,
it is recommended that a high quality 0.1μF surface mount
ceramic bypass capacitor be placed between V+ and V– with
direct short connections. In addition, V– should be tied
directly to a low impedance ground plane with minimal
routing. For dual (split) power supplies, it is recommended
that additional high quality, 0.1μF ceramic capacitors are
used to bypass V+ to ground and V– to ground, again
with minimal routing. For driving large loads (<200Ω),
additional bypass capacitance may be needed for optimal
performance. Keep in mind that small geometry (e.g., 0603
or smaller) surface mount ceramic capacitors have a much
higher self resonant frequency than do leaded capacitors,
and perform best in high speed applications.
+OUT, –OUT (Pins 4, 5/Pins 7, 14): Unltered Output
Pins. Besides driving the feedback network, each pin
can drive an additional 50Ω to ground with typical short
circuit current limiting of ±60mA. Each amplier output
is designed to drive a load capacitance of 5pF. Larger
capacitive loads should be decoupled with at least 15Ω
resistors from each output.
VTIP (Pin 5) QFN Only: This pin can normally be left oat-
ing. It determines which pair of input transistors (NPN or
PNP or both) is sensing the input signal. The VTIP pin is
set by an internal resistive divider between the supplies,
developing a default 2.8V voltage with a 5V supply. VTIP
has a Thevenin equivalent resistance of approximately
17k and can be over-driven by an external voltage. The
VTIP pin should be bypassed with a high quality ceramic
bypass capacitor of at least 0.01μF. See the Applications
Information section for more details.
SHDN (Pin 7/Pin 1): When SHDN is oating or directly
tied to V+, the LTC6405 is in the normal (active) operat-
ing mode. When the SHDN pin is connected to V–, the
LTC6405 enters into a low power shutdown state with
Hi-Z outputs.
+IN, –IN (Pins 8, 1/Pins 15, 6): Noninverting and Inverting
Input Pins of the Amplier, Respectively. For best perfor-
mance, it is highly recommended that stray capacitance
be kept to an absolute minimum by keeping printed circuit
connections as short as possible.
+OUTF, –OUTF (Pins 8, 13) QFN Only: Filtered Output
Pins. These pins have a series RC network (R = 50Ω,
C = 3.75pF) connected between the ltered and unltered
outputs. See the Applications Information section for
more details.
NC (Pin 16) QFN Only: No Connection. This pin is not
connected internally.
Exposed Pad (Pin 9/Pin 17): Tie the bottom pad to V–. If
split supplies are used, DO NOT tie the pad to ground.
(MSOP/QFN)
相关PDF资料 |
PDF描述 |
|---|---|
| LTM4600HVEV | 17 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PBGA104 |
| LTM4600HVIV | 17 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PBGA104 |
| LV5103LP | SPECIALTY ANALOG CIRCUIT, QCC40 |
| LV5103LP | SPECIALTY ANALOG CIRCUIT, QCC40 |
| LV51142T | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6405IUD | 制造商:Linear Technology 功能描述:DIFF AMP 5V 2.7GHZ R/R 16QFN |
| LTC6405IUD#PBF | 功能描述:IC DIFF AMP/DRIVER R-R 16-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| LTC6405IUD#TR | 制造商:Linear Technology 功能描述:DIFF-AMPLIFIER, 2.7GHZ, 690V/US, QFN-16, No. of Amplifiers:1, Input Offset Voltage:6mV, Bandwidth:2.7GHz, Amplifier Case Style:QFN, No. of Pins:16, Supply Voltage Range:4.5V to 5.25V, Slew Rate:690V/s, Supply Current:18mA, MSL:- , RoHS Compliant: No |
| LTC6405IUD#TRPBF | 功能描述:IC DIFF AMP/DRIVER R-R 16-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| LTC6405IUD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.7GHz, 5V, Low Noise, Rail-to-Rail Input Differential Amplifi er/Driver |
发布紧急采购，3分钟左右您将得到回复。