参数资料
| 型号： | LTC6410IUD-6#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF IF 16-QFN |
| 标准包装： | 121 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 1500 V/µs |
| -3db带宽： | 1.4GHz |
| 电压 - 输入偏移： | 400µV |
| 电流 - 电源： | 125mA |
| 电流 - 输出 / 通道： | 42mA |
| 电压 - 电源，单路/双路(±)： | 2.8 V ~ 5.5 V，±1.4 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1323 (CN2011-ZH PDF) |
LTC6410-6
11
64106fa
APPLICATIONS INFORMATION
Introduction
The LTC6410-6 is a low noise differential high speed
amplier. By default, the LTC6410-6 has 6dB voltage gain
and is designed to operate with 50Ω differential input and
output impedances. By changing (REXT), alternative con-
gurations provide input resistances of up to 400Ω, with
correspondingly lower noise gure and higher power gain.
The Block Diagram shows the basic circuit along with key
external components while Table 1 provides conguration
information. If the input is AC-coupled, the VBIAS pin sets
the input common mode voltage and therefore the output
common mode voltage.
Input Impedance
LTC6410-6 has been designed with very exible input
termination circuitry. By default, with the termination pins
connected directly to the inputs, the input impedance is
58Ω, see the Block Diagram. Internally, there is 110Ω
between each input and the opposite output (RT). Divid-
ing the resistor by the internal noise gain of 2.7 + 1 = 3.7,
29.5Ω input impedance is created (59Ω differential ). In
parallel with the 2k common mode resistance, a total of
58Ω differential input impedance is achieved. This method
of termination is used to provide lower noise gure through
the use of feedback which reduces the effective noise of
the termination resistor. By adding additional resistance in
series with the termination pins, higher input impedances
can be obtained (see Table 1). The optimum impedance
for minimizing the noise gure of the LTC6410-6 is close
to 400Ω. Because the amplier is inherently a voltage
amplier, the difference between the impedance at the
input and the output adds additional power gain as can
be seen in Table 1. These higher impedance levels can be
useful in interfacing with active mixers which can have
output impedance of 400Ω and beyond.
Input and Output Common Mode Bias
The LTC6410-6 is internally self-biased through the VBIAS
pin (see the Block Diagram). Therefore the LTC6410-6
can be AC-coupled with no external biasing circuitry. The
output will have approximately the same common mode
voltage as the input.
In the case of a DC-coupled input connection, the input
DC common mode voltage will also set the output com-
mon mode voltage. Note that a voltage divider is formed
between the VBIAS buffer output and the DC input source
impedance.
The VBIAS pin has an internal voltage divider which will
self bias to approximately 1.4V on a 3V supply (0.47
VSUPPLY). An external capacitor of 0.1μF to ground is
recommended to bypass the pin. The resistance of the pin
is 3k. See Distortion vs Common Mode graph.
For increased common mode accuracy, the +TERM and
–TERM pins can be AC-coupled to the inputs with capaci-
tors (CEXT). This coupling prevents the feedback from the
termination resistance from creating additional DC com-
mon mode voltage error. The GCM and VOSCM of the DC
Electrical Characteristics table reect the less accurate
DC-coupled scenario.
The termination inputs are part of a high speed feedback
loop. The physical length of the termination loop (REXT
and CEXT) must be minimized to maintain stability and
minimize gain peaking.
Gain
Internally, the LTC6410-6 has a voltage gain of 2.7V/V.
The default source and load resistances in most of the
data sheet are assumed to be 50Ω differential. Due to the
input and output resistance of the LTC6410-6 being 58Ω
and 22Ω respectively, the overall voltage gain in a 50Ω
system is 6dB (2V/V). Other source and load resistances
will produce different gains due to the resistive dividers.
Figure 1 is a system diagram for calculating gain.
Figure 1
RIN
64106 F01
RS
RLOAD
LTC6410-6
ROUT
22Ω
VS
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6412CUF#TRPBF | IC VGA ANLG-CNTRL 31DB 24-QFN |
| LTC6416IDDB#TRPBF | IC DIFF 16BIT BUFFER 10-DFN |
| LTC6800HDD#TRPBF | IC OP AMP INSTR R-R I/O 8-DFN |
| LTC6910-2HTS8#TRPBF | IC PGA DIGITAL R-R I/O TSOT23-8 |
| LTC6911HMS-2#TRPBF | IC PGA DIGITAL R-R DUAL 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6410IUD-6-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Distortion, Low Noise Differential IF Amplifi er with Confi gurable Input Impedance |
| LTC6411 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.7GHz, 5V, Low Noise,Rail-to-Rail Input Differential Amplifier/Driver |
| LTC6412 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 14-Bit 250Msps |
| LTC6412CUF | 制造商:LINER 制造商全称:Linear Technology 功能描述:800MHz, 31dB Range Analog-Controlled VGA |
| LTC6412CUF#PBF | 功能描述:IC VGA ANLG-CNTRL 31DB 24-QFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。