- 您现在的位置：买卖IC网 > PDF目录1935 > LTC6601IUF-1#TRPBF (Linear Technology)IC DRVR FILTER/ADC LN 20-QFN PDF资料下载
参数资料
| 型号： | LTC6601IUF-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/40页 |
| 文件大小： | 0K |
| 描述： | IC DRVR FILTER/ADC LN 20-QFN |
| 标准包装： | 2,500 |
| 频率 - 截止或中心： | 28Mhz |
| 滤波器数： | 3 |
| 滤波器阶数： | 2nd |
| 电源电压： | 2.7 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC6601-1
17
66011f
APPLICATIONS INFORMATION
potential halfway between the V+ and V– pins. Whenever
this pin is not hard tied to a low impedance ground plane,
a high quality ceramic capacitor should be used to bypass
the VOCM pin to a low impedance ground plane (see Layout
Considerations). The LTC6601’s internal common mode
feedback path forces accurate output phase balancing to
reduce even order harmonics, and centers each individual
output about the potential set by the VOCM pin.
VOUTCM = VOCM =
VOUT+ + VOUT–
2
The outputs (OUT+ and OUT–) of the LTC6601 are capable
of swinging rail-to-rail. They can source or sink up to ap-
proximately 75mA of current. Load capacitances should
be decoupled with at least 25Ω of series resistance from
each output.
The LTC6601 Electrical Characteristics table species an
input referred offset. This specication actually lumps volt-
age offsets due to offset bias currents (IOS), and amplier
voltage offset into one specication. To refer this specica-
tion to the output, you simply multiply the specication
by the noise gain the LTC6601 is congured in:
VOSODIFF = 1 + Gain
where Gain is the closed loop gain in the particular lter
application:
Gain= R2
R1
COMPONENT INPUT PIN PROTECTION
All of the LTC6601 pins with the exception of V+ and V– are
protected with steering diodes to either power supply. In
the event that a pin is driven beyond the supply rails, the
excess current should be limited to under 10mA to prevent
damage to the IC.
BIAS Pin
The LTC6601 has a BIAS pin (Pin 3) whose function is to
tailor both performance and power of the LTC6601. The
pin has a Thevenin equivalent impedance of approximately
150kΩ to a voltage source whose potential is 1.15V above
the V– supply. This pin has xed logic levels relative to V–
(see the Electrical Characteristics table), and can be driven
by an external source keeping in mind its equivalent input
impedance and equivalent input voltage. If the BIAS pin is
oated, care should be taken to control external leakage
currents to this pin to under 1μA to prevent putting the
LTC6601 an undesired state.
If BIAS is tied to the positive supply, the LTC6601 dif-
ferential lter will be in a fully active state congured for
highest performance (lowest noise and lowest distortion).
If the BIAS pin is oated or left unconnected, the LTC6601
lter will be in a fully active state, with amplier currents
reduced and performance scaled back to preserve power
consumption. If the BIAS pin is tied to the most negative
supply (V–), the LTC6601 will be placed into a low power
shutdown mode with amplier outputs disabled. In this
state, the LTC6601 draws approximately 350μA.
In low power shutdown, all internal biasing current sources
are shut off, and the output pins, OUT+ and OUT–, will each
appear as open collectors with a non-linear capacitor in
parallel and steering diodes to either supply. The turn-on
and turn-off time constant between states are on the order
of 0.4μs. Using this function to wire-OR outputs together
is not recommended.
General Design and Usage
As levels of integration have increased and correspond-
ingly, system supply voltages decreased, there has been
a need for ADCs to process signals differentially in order
to maintain good signal-to-noise ratios. These ADCs are
typically supplied from a single supply voltage which
can be as low as 3V (2.7V min), and will have an optimal
common mode input range near mid-supply. The LTC6601
makes interfacing to these ADCs easy, by providing anti-
alias ltering, single-ended to differential conversion and
common mode level shifting (translation). Figure 3 shows
a general application of this. The low frequency gain to
VOUTDIFF from VIN is simply:
VOUTDIFF = VOUT+ –VOUT– ≈
R2
R1
VINDIFF
The differential output voltage (VOUT+–VOUT–)iscompletely
independent of input and output common mode voltages,
or the voltage at the common mode pin. This makes the
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6602IUF#PBF | IC FILTER BANDPASS/LOWPASS 24QFN |
| LTC6603CUF#PBF | IC FILTER LOWPASS 24-QFN |
| LTC6605IDJC-10#TRPBF | IC FILTER 10MHZ DUAL 22-DFN |
| LTC6605IDJC-14#TRPBF | IC FILTER 14MHZ DUAL 22-DFN |
| LTC6605IDJC-7#TRPBF | IC FILTER 7MHZ DUAL 22-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6601IUF-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Power, Low Distortion, 5MHz to 27MHz, Pin Confi gurable Filter/ADC Driver |
| LTC6601IUF-2#PBF | 功能描述:IC DRVR FILTER/ADC LN 20-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC6601IUF-2#PBF | 制造商:Linear Technology 功能描述:SC-Filters/Active RCLow Power Low Disto |
| LTC6601IUF-2#TRPBF | 功能描述:IC FILTER/ADC DVR LP LD 20-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC6601IUF-2PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Power, Low Distortion, 5MHz to 27MHz, Pin Confi gurable Filter/ADC Driver |
发布紧急采购，3分钟左右您将得到回复。