- 您现在的位置：买卖IC网 > PDF目录15967 > LTC6803IG-3#TRPBF (Linear Technology)IC MONITOR BATT STACK 44-SSOP PDF资料下载
参数资料
| 型号： | LTC6803IG-3#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/40页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR BATT STACK 44-SSOP |
| 标准包装： | 2,000 |
| 功能： | 电池监控器，过压/欠压保护 |
| 电池化学： | 多化学成分，超级电容器 |
| 电源电压： | 4 V ~ 55 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-FSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 44-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC6803-1/LTC6803-3
OPERATION
when V + = 44V. All circuits are turned off except the serial
interface and the voltage regulator. For the lowest possible
standby current consumption all SPI logic inputs should
be set to logic 1 level. The LTC6803 can be programmed
for standby mode by setting the comparator duty cycle
configuration bits, CDC[2:0], to 0. If the part is put into
standby mode while ADC measurements are in progress,
the measurements will be interrupted and the cell voltage
registers will be in an indeterminate state. To exit standby
mode, the CDC bits must be written to a value other than 0.
MEASURE MODE
The LTC6803 is in measure mode when the CDC bits are
programmed with a value from 1 to 7. When CDC = 1 the
LTC6803 is on and waiting for a start ADC conversion
command. When CDC is 2 through 7 the IC monitors each
cell voltage and produces an interrupt signal on the SDO
pin indicating all cell voltages are within the UV and OV
limits. The value of the CDC bits determines how often
the cells are monitored, and how much average supply
current is consumed.
There are two methods for indicating the UV/OV inter-
rupt status: toggle polling (using a 1kHz output signal)
and level polling (using a high or low output signal). The
polling methods are described in the Serial Port section.
The UV/OV limits are set by the V UV and V OV values in the
configuration registers. When a cell voltage exceeds the
UV/OV limits a bit is set in the flag register. The UV and
OV flag status for each cell can be determined using the
Read Flag Register Group .
An ADC measurement can be requested at any time when
the IC is in measure mode. To initiate cell voltage measure-
ments while in measure mode, a Start A/D Conversion is
sent. After the command has been sent, the LTC6803 will
indicate the A/D converter status via toggle polling or level
polling (as described in the Serial Port section). During
cell voltage measurement commands, the UV and OV flags
(within the flag register group) are also updated. When
the measurements are complete, the part will continue
monitoring UV and OV conditions at the rate designated
by the CDC bits. Note that there is a 5μs window during
each UV/OV comparison cycle where an ADC measure-
ment request may be missed. This is an unlikely event.
14
For example, the comparison cycle is 2 seconds when
CDC = 7. Use the CLEAR command to detect missing
ADC commands.
Operating with Less than 12 Cells
If fewer than 12 cells are connected to the LTC6803, the
unused input channels must be masked. The MCxI bits in
the configuration registers are used to mask channels. In
addition, the LTC6803 can be configured to automatically
bypass the measurements of the top 2 cells, reducing power
consumption and measurement time. If the CELL10 bit is
high, the inputs for cell 11 and cell 12 are masked and only
the bottom 10 cell voltages will be measured. By default,
the CELL10 bit is low, enabling measurement of all 12 cell
voltages. Additional information regarding operation with
less than 12 cells is provided in the applications section.
ADC RANGE AND OUTPUT FORMAT
The ADC outputs a 12-bit code with an offset of 0x200
(512 decimal). The input voltage can be calculated as:
V IN = (D OUT – 512) ? V LSB ; V LSB = 1.5mV
where D OUT is a decimal integer.
For example, a 0V input will have an output reading
of 0x200. An ADC reading of 0x000 means the input
was –0.768V. The absolute ADC measurement range is
–0.768V to 5.376V. The resolution is V LSB = 1.5mV = (5.376
+ 0.768)/2 12 . The useful range is –0.3V to 5V. This range
allows monitoring super capacitors, which could have small
negative voltage. Inputs below –0.3V exceed the absolute
maximum rating of the C pins. If all inputs are negative
then the ADC range is reduced to –0.1V. Inputs above 5V
will have noisy ADC readings (see Typical Performance
Characteristics curves).
ADC MEASUREMENTS DURING CELL BALANCING
The primary cell voltage ADC measurement commands
(STCVAD and STOWAD) automatically turn off a cell’s
discharge switch while its voltage is being measured. The
discharge switches for the cell above and the cell below will
also be turned off during the measurement. For example,
discharge switches S4, S5 and S6 will be off while cell 5
is being measured. The UV/OV comparison conversions in
680313fa
相关PDF资料 |
PDF描述 |
|---|---|
| GWN0.75BK25 | GRIP WRAP 3/4" BLACK 25' |
| ISC1812ESR82K | INDUCTOR WW 820NH 10% 1812 |
| 415-0010-006 | CABLE SMB/SMB 6" RG-179DS |
| FGLG.16BK | INSULTHERM TRU-FIT 16AWG 500' |
| GSM06DRSD-S664 | CONN EDGECARD 12POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6803IG-4#PBF | 功能描述:IC MONITOR BATT STACK MC 44-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC6803IG-4#TRPBF | 功能描述:IC MONITOR BATT STACK 44-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC6803IG-4PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Multicell Battery Stack Monitor |
| LTC6804-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effciency Bidirectional Multicell Battery Balancer |
| LTC6804-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effciency Bidirectional Multicell Battery Balancer |
发布紧急采购，3分钟左右您将得到回复。