参数资料
型号: LTC6902IMS#PBF
厂商: Linear Technology
文件页数: 3/16页
文件大小: 0K
描述: IC OSC SILICON 20MHZ 10MSOP
标准包装: 50
类型: 振荡器 - 硅
频率: 100kHz ~ 20MHz
电源电压: 2.7 V ~ 5.5 V
电流 - 电源: 2.5mA
工作温度: -40°C ~ 85°C
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
包装: 管件
供应商设备封装: 10-MSOP
安装类型: 表面贴装
LTC6902
11
6902f
THEORY OF OPERATIO
U
fMAX
fMIN
128 STEPS
TIME
69012 F05
3200
fMASTER
FREQUENCY
τSTEP
τSTEP =
τREPEAT
3200 512
fMASTER
τREPEAT =
Figure 5
APPLICATIO S I FOR ATIO
WU
UU
SELECTING THE DIVIDER SETTING AND RSET VALUE
The LTC6902’s master oscillator has a frequency range
spanning 0.1MHz to 20MHz. However, accuracy may
suffer if the master oscillator is operated at greater than
10MHz with a supply voltage lower than 4V. A program-
mable divider extends the frequency range to greater than
three decades. Additional frequency division may occur
depending on the multiphase mode selected. The
multiphase mode and the parameter M are generally
dependent on the application’s requirement and usually
do not offer any additional design flexibility.
The LTC6902’s master oscillator covers a 200:1 range
while the programmable divider has 10:1 steps (1, 10,
100). This wide frequency range coupled with the part’s
programmable divider yields at least two solutions for any
desired output frequency (the exception being the highest
output frequencies that cannot be divided down). Choos-
ing the best divider setting and the correct RSET resistor
value depends on the application.
For spread spectrum frequency modulated (SSFM) appli-
cations, choose the highest divider setting. This forces the
master oscillator to run at its highest frequency. The
pseudorandom signal generator is clocked by the master
oscillator, not the output, and the faster the signal moves
the greater the improvement in EMC performance. For
most applications the multiphase mode is determined by
the specific application’s need. For these applications, the
parameter M is predetermined and fixed. Table 1 lists the
recommended output (fOUT) frequency range for each
divider setting when using SSFM.
clock cycle. Note that the shift register clock is the master
oscillator’s output divided by 3200. This results in a some-
what slow moving modulating signal where each step is
separated in time by 3200/fMASTER seconds and the pseu-
dorandom sequence repeats every (512 3200)/fMASTER
seconds.
The servo loop in the LTC6902 cannot respond instanta-
neously to each step due to its limited bandwidth. The
VMOD voltage steps are converted to frequency steps by
the servo loop. The servo loop has a bandwidth of about
25kHz that limits the frequency change rate and softens
corners of the waveform. This is beneficial when the
LTC6902 is used to clock switching regulators as will be
discussed in the Applications Information section. Fig-
ure 5 illustrates the how the output frequency varies over
time.
相关PDF资料
PDF描述
VE-B4M-IU-S CONVERTER MOD DC/DC 10V 200W
LTC6992HS6-3#TRMPBF IC OSC SILICON 1MHZ TSOT23-6
VE-B4L-IU-S CONVERTER MOD DC/DC 28V 200W
VE-B4K-IU-S CONVERTER MOD DC/DC 40V 200W
VE-B4J-IU-S CONVERTER MOD DC/DC 36V 200W
相关代理商/技术参数
参数描述
LTC6903 制造商:LINER 制造商全称:Linear Technology 功能描述:1kHz to 68MHz Serial Port Programmable Oscillator
LTC6903_12 制造商:LINER 制造商全称:Linear Technology 功能描述:1kHz to 68MHz Serial Port Programmable Oscillator
LTC6903CMS8 功能描述:IC OSC SILICON 68MHZ 8-MSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:45 系列:- 类型:温度 - 补偿晶体振荡器(TCXO) 计数:- 频率:25MHz 电源电压:3.135 V ~ 3.465 V 电流 - 电源:1.5mA 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC(0.295",7.50mm 宽) 包装:管件 供应商设备封装:16-SOIC W 安装类型:表面贴装
LTC6903CMS8#PBF 功能描述:IC OSC SILICON 68MHZ 8-MSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 标准包装:3,000 系列:- 类型:振荡器 - 晶体 计数:- 频率:- 电源电压:2.3 V ~ 5.5 V 电流 - 电源:1.07mA 工作温度:-30°C ~ 80°C 封装/外壳:SOT-665 包装:带卷 (TR) 供应商设备封装:SS迷你型-5D 安装类型:表面贴装 其它名称:AN8955SSMTXLTR
LTC6903CMS8#PBF 制造商:Linear Technology 功能描述:Programmable Oscillator IC