- 您现在的位置：买卖IC网 > PDF目录15336 > LTC692CS8#TRPBF (Linear Technology)IC MPU SUPERVISORY CIRCUIT 8SOIC PDF资料下载
参数资料
| 型号： | LTC692CS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISORY CIRCUIT 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.4V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
LTC692/LTC693
APPLICATIONS INFORMATION
Microprocessor Reset
The LTC692/LTC693 use a bandgap voltage reference
and a precision voltage comparator C1 to monitor the
5V supply input on V CC (see Block Diagram). When V CC
falls below the reset voltage threshold, the RESET output
is forced to active low state. The reset voltage threshold
accounts for a 10% variation on V CC , so the RESET output
becomes active low when V CC falls below 4.50V (4.40V
typical). On power-up, the RESET signal is held active low
for a minimum of 140ms after reset voltage threshold is
reached to allow the power supply and microprocessor to
stabilize. The reset active time is adjustable on the LTC693.
On power down, the RESET signal remains active low
even with V CC as low as 1V. This capability helps hold the
microprocessor in stable shutdown condition. Figure 1
shows the timing diagram of the RESET signal.
The precision voltage comparator, C1, typically has 40mV
of hysteresis which ensures that glitches at the V CC pin do
not activate the RESET output. Response time is typically
10μs. To help prevent mistriggering due to transient loads,
V CC pin should be bypassed with a 0.1μF capacitor with
the leads trimmed as short as possible.
The LTC693 has two additional outputs: RESET and
LOW LINE. RESET is an active high output and is the
inverse of RESET . LOW LINE is the output of the preci-
sion voltage comparator, C1. When V CC falls below the
reset voltage threshold, LOW LINE goes low. LOW LINE
returns high as soon as V CC rises above the reset volt-
age threshold.
Battery Switchover
The battery switchover circuit compares V CC to the V BATT
input, and connects V OUT to whichever is higher. When
V CC rises to 70mV above V BATT , the battery switchover
comparator, C2, connects V OUT to V CC through a charge
pumped NMOS power switch, M1. When V CC falls to 50mV
above V BATT , C2 connects V OUT to V BATT through a PMOS
switch, M2. C2 has typically 20mV of hysteresis to prevent
spurious switching when V CC remains nearly equal to V BATT .
The response time of C2 is approximately 20μs.
During normal operation, the LTC692/LTC693 use a charge
pumped NMOS power switch to achieve low dropout and
low supply current. This power switch can deliver up to
50mA to V OUT from V CC and has a typical on-resistance
of 5Ω. The V OUT pin should be bypassed with a capaci-
tor of 0.1μF or greater to ensure stability. Use of a larger
bypass capacitor is advantageous for supplying current
to heavy transient loads.
When operating currents larger than 50mA are required
from V OUT , or a lower dropout (V CC – V OUT voltage dif-
ferential) is desired, the LTC693 should be used. This
product provides BATT ON output to drive the base of the
external PNP transistor (Figure 2). If higher currents are
needed with the LTC692, a high current Schottky diode can
be connected from the V CC pin to the V OUT pin to supply
the extra current.
V CC
V2
V1
V2
V1 = RESET VOLTAGE THRESHOLD
V2 = RESET VOLTAGE THRESHOLD +
V1
RESET THRESHOLD HYSTERESIS
RESET
t 1
t 1
t 1 = RESET ACTIVE TIME
LOW LINE
692_3 ? F01
Figure 1. Reset Active Time
0692fb
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3872ITS8#TRMPBF | IC REG CTRLR BST PWM CM TSOT23-8 |
| B41042A8157M | 150UF 63V 10X25 SINGLE END |
| LTC3872IDDB#TRMPBF | IC REG CTRLR BST PWM CM 8-DFN |
| B41042A6187M | 180UF 50V 10X20 SINGLE END |
| LT1246CS8#TRPBF | IC REG CTRLR ISO PWM CM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC692I | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC692IN8 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC692IS8 | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC692IS8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC692IS8#TR | 功能描述:IC SUPERVISORY CIRCUIT MPU 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。