- 您现在的位置：买卖IC网 > PDF目录15333 > LTC692IS8#PBF (Linear Technology)IC MPU SUPERVISORY CIRCUIT 8SOIC PDF资料下载
参数资料
| 型号： | LTC692IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISORY CIRCUIT 8SOIC |
| 标准包装： | 100 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.4V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
LTC692/LTC693
PIN FUNCTIONS
BATT ON: Battery On Logic Output from Comparator C2.
BATT ON goes low when V OUT is internally connected to
V CC . The output typically sinks 35mA and can provide base
drive for an external PNP transistor to increase the output
current above the 50mA rating of V OUT . BATT ON goes high
when V OUT is internally switched to V BATT .
CE IN: Logic Input to the Chip Enable Gating Circuit. CE IN
can be derived from microprocessor’s address line and/or
decoder output. See Applications Information section and
Figure 5 for additional information.
CE OUT : Logic Output on the Chip Enable Gating Circuit.
When V CC is above the reset voltage threshold, CE OUT is
a buffered replica of CE IN. When V CC is below the reset
voltage threshold CE OUT is forced high (see Figure 5).
GND: Ground Pin.
LOW LINE: Logic Output from Comparator C1. LOW LINE
indicates a low line condition at the V CC input. When V CC
falls belo w the reset voltage threshold (4.40V typically),
LOW LINE goes low. As soon as V CC rises above the reset
voltage threshold, LOW LINE returns high (see Figure 1).
LOW LINE goes low when V CC drops below V BATT (see
Table 1).
OSC IN: Oscillator Input. OSC IN can be driven by an
external clock signal or an external capacitor can be
connected between OSC IN and GND when OSC SEL is
forced low. In this con?guration the nominal reset active
time and watchdog timeout period are determined by the
number of clocks or set by the formula (see Applications
Information section). When OSC SEL is high or ?oating,
the internal oscillator is enabled and the reset active time
is ?xed at 200ms typical. OSC IN selects between the 1.6
seconds and 100ms typical watchdog timeout periods. In
both cases the timeout period immediately after a reset is
1.6 seconds typical.
OSC SEL: Oscillator Selection Input. When OSC SEL is
high or ?oating, the internal oscillator sets the reset active
time and watchdog timeout period. Forcing OSC SEL low
PFI: Power Failure Input. PFI is the noninverting input
to the power-fail comparator, C3. The inverting input is
internally connected to a 1.3V reference. The power failure
output remains high when PFI is above 1.3V and goes
low when PFI is below 1.3V. Connect PFI to GND or V OUT
when C3 is not used.
PFO : Power Failure Output from C3. PFO remains high
when PFI is above 1.3V and goes low when PFI is below
1.3V. When V CC is lower than V BATT , C3 is shut down and
PFO is forced low.
RESET: Logic Output for μP Reset Control. Whenever V CC
falls below either the reset voltage threshold (4.40V typi-
cally) or V BATT , RESET goes active low. After V CC returns
to 5V, reset pulse generator forces RESET to remain active
low for a minimum of 140ms. When the watchdog timer is
enabled but not serviced prior to a preset timeout period,
reset pulse generator also forces RESET to active low for
a minimum of 140ms for every preset timeout period
(see Figure 11). The reset active time is adjustable on
the LTC693. An external pushbutton reset can be used in
connection with the RESET output. See Pushbutton Reset
in the Applications Information section.
RESET: RESET is an Active High Logic Output. It is the
inverse of RESET .
V BATT : Backup Battery Input. When V CC falls below V BATT ,
auxiliary power connected to V BATT is delivered to V OUT
through PMOS switch, M2. If backup battery or auxiliary
power is not used, V BATT should be connected to GND.
V CC : 5V Supply Input. The V CC pin should be bypassed
with a 0.1μF capacitor.
V OUT : Voltage Output for Backed-Up Memory. Bypass with
a capacitor of 0.1μF or greater. During normal operation,
V OUT obtains power from V CC through an NMOS power
switch, M1, which can deliver up to 50mA and has a typical
on-resistance of 5Ω. When V CC is lower than V BATT , V OUT
is internally switched to V BATT . If V OUT and V BATT are not
used, connect V OUT to V CC .
allows OSC IN to be driven from an external clock signal
or an external capacitor to be connected between OSC
IN and GND.
0692fb
7
相关PDF资料 |
PDF描述 |
|---|---|
| ELJ-RER10JF3 | INDUCTOR 100NH 5% FIXED SMD |
| VI-JW1-EY-F1 | CONVERTER MOD DC/DC 12V 50W |
| LD2-680-R | INDUCTOR PWR METL DRUM CORE 68UH |
| GCM28DSEF | CONN EDGECARD 56POS .156 EYELET |
| VI-2WV-EY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC692IS8-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC693 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC6930 | 制造商:LINER 制造商全称:Linear Technology 功能描述:32.768kHz to 8.192MHz Precision μPower Oscillators |
| LTC6930CDCB-4.19#PBF | 制造商:Linear Technology 功能描述:Silicon Oscillator 8-Pin DFN EP |
| LTC6930CDCB-4.19#TRMPBF | 功能描述:IC OSC SILICON 4.194304MHZ 8-DFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 标准包装:3,000 系列:- 类型:振荡器 - 晶体 计数:- 频率:- 电源电压:2.3 V ~ 5.5 V 电流 - 电源:1.07mA 工作温度:-30°C ~ 80°C 封装/外壳:SOT-665 包装:带卷 (TR) 供应商设备封装:SS迷你型-5D 安装类型:表面贴装 其它名称:AN8955SSMTXLTR |
发布紧急采购，3分钟左右您将得到回复。