- 您现在的位置：买卖IC网 > Datasheet目录868 > LTM4609IV#PBF (Linear Technology)IC BUCK/BOOST SYNC ADJ 4A 141LGA Datasheet资料下载
参数资料
| 型号： | LTM4609IV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC BUCK/BOOST SYNC ADJ 4A 141LGA |
| 产品培训模块： | Buck-Boost uModule Regulators High Voltage µModule DC/DC Regulators Power Module vs. Discrete DC to DC |
| 软件下载： | LTM4609 Spice Model |
| 设计资源： | DC1477A Design Files LTM4609IV#PBF Footprint.bxl |
| 特色产品： | μModule Products DC/DC μModule Regulator Family |
| 标准包装： | 119 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 4.5V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 0.8 ~ 34 V |
| 电流 - 输出（最大）： | 4A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 141-LGA |
| 尺寸/尺寸： | 0.59" L x 0.59" W x 0.11" H（15.0mm x 15.0mm x 2.8mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 98% |
| 配用： | DC1477A-ND - BOARD EVAL LTM4609 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTM4609
APPLICATIONS INFORMATION
I OUT(MAX) ? ( V OUT – V IN(MIN) )
C OUT ? V OUT ? ?
V 2IN ? ( V OUT(MAX) – V IN )
V 2OUT(MAX) ? ? ? I OUT(MAX) ? Ripple%
V OUT ? ( V IN(MAX) – V OUT )
V IN(MAX) ? ? ? I OUT(MAX) ? Ripple%
This makes it advisable to properly derate the input capaci-
tor, or choose a capacitor rated at a higher temperature
than required. Always contact the capacitor manufacturer
for derating requirements.
Output Capacitors
In boost mode, the discontinuous current shifts from the
input to the output, so the output capacitor C OUT must be
capable of reducing the output voltage ripple.
For boost and buck modes, the steady ripple due to charg-
ing and discharging the bulk capacitance is given by:
V RIPPLE,BOOST =
ripple Δ I L is typically set to 20% to 40% of the maximum
inductor current. In the inductor design, the worst cases
in continuous mode are considered as follows:
L BOOST ≥
L BUCK ≥
where:
? is operating frequency, Hz
Ripple% is allowable inductor current ripple, %
V RIPPLE,BUCK =
V OUT ? ( V IN(MAX) – V OUT )
8 ? L ? C OUT ? V IN(MAX) ? ? 2
V OUT(MAX) is maximum output voltage, V
V IN(MAX) is maximum input voltage, V
V OUT is output voltage, V
I OUT(MAX,BOOST) = ?
160mV ?I L ? V IN
? R SENSE
The steady ripple due to the voltage drop across the ESR
(effective series resistance) is given by:
V ESR,BUCK = ?I L(MAX) ? ESR
V ESR,BOOST =I L(MAX) ? ESR
The LTM4609 is designed for low output voltage ripple.
The bulk output capacitors defined as C OUT are chosen
with low enough ESR to meet the output voltage ripple and
transient requirements. C OUT can be the low ESR tantalum
capacitor, the low ESR polymer capacitor or the ceramic
capacitor. Multiple capacitors can be placed in parallel to
meet the ESR and RMS current handling requirements. The
typical capacitance is 300μF. Additional output filtering may
be required by the system designer, if further reduction of
output ripple or dynamic transient spike is required. Table 3
shows a matrix of different output voltages and output
capacitors to minimize the voltage droop and overshoot
at a current transient.
Inductor Selection
The inductor is chiefly decided by the required ripple cur-
rent and the operating frequency. The inductor current
I OUT(MAX) is maximum output load current, A
The inductor should have low DC resistance to reduce the
I 2 R losses, and must be able to handle the peak inductor
current without saturation. To minimize radiated noise,
use a toroid, pot core or shielded bobbin inductor. Please
refer to Table 3 for the recommended inductors for dif-
ferent cases.
R SENSE Selection and Maximum Output Current
R SENSE is chosen based on the required inductor current.
Since the maximum inductor valley current at buck mode
is much lower than the inductor peak current at boost
mode, different sensing resistors are suggested to use
in buck and boost modes.
The current comparator threshold sets the peak of the
inductor current in boost mode and the maximum inductor
valley current in buck mode. In boost mode, the allowed
maximum average load current is:
– ?
2 ? V OUT
where Δ I L is peak-to-peak inductor ripple current.
4609ff
For more information www.linear.com/LTM4609
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTM4612IV#PBF | IC BUCK SYNC ADJ 5A 133LGA |
| LTM4613MPV#PBF | IC UMODULE DC/DC 8A 133-LGA |
| LTM4614IV#PBF | IC UMODULE DC/DC DUAL 4A 144LGA |
| LTM4615IV#PBF | IC SWIT REG BUCK 4A ADJ 144LGA |
| LTM4618IV#PBF | IC DC-DC UMODULE BUCK 6A 84-LGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM4609IY#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERT 0.8-36V 10A 制造商:Linear Technology 功能描述:BUCK / BOOST 4/10A 0.8-34V |
| LTM4609MPV#PBF | 功能描述:IC UMODULE BUCK-BOOST 141-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM4609MPY#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERT 0.8-36V 10A 制造商:Linear Technology 功能描述:DP-uModule, 36Vin, 34Vout High Efficiency Buck-Boost DC/DC uModules |
| LTM4611 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow VIN, 15A DC/DC μModule Regulator |
| LTM4611EV#PBF | 功能描述:IC UMODULE DC/DC LV 15A 133-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。