- 您现在的位置：买卖IC网 > Datasheet目录868 > LTM4609IV#PBF (Linear Technology)IC BUCK/BOOST SYNC ADJ 4A 141LGA Datasheet资料下载
参数资料
| 型号： | LTM4609IV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/28页 |
| 文件大小： | 0K |
| 描述： | IC BUCK/BOOST SYNC ADJ 4A 141LGA |
| 产品培训模块： | Buck-Boost uModule Regulators High Voltage µModule DC/DC Regulators Power Module vs. Discrete DC to DC |
| 软件下载： | LTM4609 Spice Model |
| 设计资源： | DC1477A Design Files LTM4609IV#PBF Footprint.bxl |
| 特色产品： | μModule Products DC/DC μModule Regulator Family |
| 标准包装： | 119 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 4.5V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 0.8 ~ 34 V |
| 电流 - 输出（最大）： | 4A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 141-LGA |
| 尺寸/尺寸： | 0.59" L x 0.59" W x 0.11" H（15.0mm x 15.0mm x 2.8mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 98% |
| 配用： | DC1477A-ND - BOARD EVAL LTM4609 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTM4609
PIN FUNCTIONS
V IN (Bank 1): Power Input Pins. Apply input voltage be-
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between V IN pins
and PGND pins.
V OUT (Bank 5): Power Output Pins. Apply output load
between these pins and PGND pins. Recommend placing
output decoupling capacitance directly between these pins
and PGND pins.
PGND (Bank 6): Power Ground Pins for Both Input and
Output Returns.
SW1, SW2 (Bank 4, Bank 2): Switch Nodes. The power
inductor is connected between SW1 and SW2.
R SENSE (Bank 3): Sensing Resistor Pin. The sensing resis-
tor is connected from this pin to PGND.
SENSE + (Pin A4): Positive Input to the Current Sense and
Reverse Current Detect Comparators.
SENSE – (Pin A5): Negative Input to the Current Sense and
Reverse Current Detect Comparators.
EXTV CC (Pin F6): External V CC Input. When EXTV CC exceeds
5.7V, an internal switch connects this pin to INTV CC and
shuts down the internal regulator so that the controller and
gate drive power is drawn from EXTV CC . Do not exceed
7V at this pin and ensure that EXTV CC < V IN
INTV CC (Pin F5): Internal 6V Regulator Output. This pin
is for additional decoupling of the 6V internal regulator.
Do not source more than 40mA from INTV CC .
PLLIN (Pin B9): External Clock Synchronization Input
to the Phase Detector. This pin is internally terminated
to SGND with a 50k resistor. The phase-locked loop will
force the rising bottom gate signal of the controller to be
synchronized with the rising edge of PLLIN signal.
PLLFLTR (Pin B8): The lowpass filter of the phase-locked
loop is tied to this pin. This pin can also be used to set the
frequency of the internal oscillator with an AC or DC volt-
age. See the Applications Information section for details.
SS (Pin A6): Soft-Start Pin. Soft-start reduces the input
surge current from the power source by gradually increas-
ing the controller’s current limit.
STBYMD (Pin A10): LDO Control Pin. Determines whether
the internal LDO remains active when the controller is shut
down. See Operations section for details. If the STBYMD
pin is pulled to ground, the SS pin is internally pulled to
ground to disable start-up and thereby providing a single
control pin for turning off the controller. An internal de-
coupling capacitor is tied to this pin.
V FB (Pin B6): The Negative Input of the Error Amplifier.
Internally, this pin is connected to V OUT with a 100k preci-
sion resistor. Different output voltages can be programmed
with an additional resistor between V FB and SGND pins.
See the Applications Information section.
FCB (Pin A9): Forced Continuous Control Input. The voltage
applied to this pin sets the operating mode of the module.
When the applied voltage is less than 0.8V, the forced
continuous current mode is active in boost operation and
the skip cycle mode is active in buck operation. When the
pin is tied to INTV CC , the constant frequency discontinuous
current mode is active in buck or boost operation. See the
Applications Information section.
SGND (Pin A7): Signal Ground Pin. This pin connects to
PGND at output capacitor point.
COMP (Pin B7): Current Control Threshold and Error
Amplifier Compensation Point. The current comparator
threshold increases with this control voltage. The voltage
ranges from 0V to 2.4V.
PGOOD (Pin B5): Output Voltage Power Good Indicator.
Open drain logic output that is pulled to ground when the
output voltage is not within ±7.5% of the regulation point.
RUN (Pin A8): Run Control Pin. A voltage below 1.6V will
turn off the module. There is a 100k resistor between the
RUN pin and SGND in the module. Do not apply more than
6V to this pin. See the Applications Information section.
4609ff
For more information www.linear.com/LTM4609
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTM4612IV#PBF | IC BUCK SYNC ADJ 5A 133LGA |
| LTM4613MPV#PBF | IC UMODULE DC/DC 8A 133-LGA |
| LTM4614IV#PBF | IC UMODULE DC/DC DUAL 4A 144LGA |
| LTM4615IV#PBF | IC SWIT REG BUCK 4A ADJ 144LGA |
| LTM4618IV#PBF | IC DC-DC UMODULE BUCK 6A 84-LGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM4609IY#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERT 0.8-36V 10A 制造商:Linear Technology 功能描述:BUCK / BOOST 4/10A 0.8-34V |
| LTM4609MPV#PBF | 功能描述:IC UMODULE BUCK-BOOST 141-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM4609MPY#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERT 0.8-36V 10A 制造商:Linear Technology 功能描述:DP-uModule, 36Vin, 34Vout High Efficiency Buck-Boost DC/DC uModules |
| LTM4611 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow VIN, 15A DC/DC μModule Regulator |
| LTM4611EV#PBF | 功能描述:IC UMODULE DC/DC LV 15A 133-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。