- 您现在的位置：买卖IC网 > PDF目录20302 > LTM8023IY#PBF (Linear Technology)IC DC/DC UMODULE 2A 50LGA PDF资料下载
参数资料
| 型号： | LTM8023IY#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC DC/DC UMODULE 2A 50LGA |
| 产品目录绘图： | LTM8022-8023 |
| 标准包装： | 168 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 3.6V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 0.8 ~ 10 V |
| 电流 - 输出（最大）： | 2A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 50-BGA |
| 尺寸/尺寸： | 0.44" L x 0.35" W x 0.13" H（11.3mm x 9.0mm x 3.4mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
LTM8023
OPERATION
The LTM8023 is a standalone nonisolated step-down
switching DC/DC power supply. It can deliver up to 2A of
DC output current with only bulk external input and output
capacitors. This module provides a precisely regulated
output voltage programmable via one external resistor
from 0.8V DC to 10V DC . The input voltage range is 3.6V to
36V. Given that the LTM8023 is a step-down converter,
make sure that the input voltage is high enough to support
the desired output voltage and load current. A simplified
Block Diagram is given on the previous page.
The LTM8023 contains a current mode controller, power
switching element, power inductor, power Schottky diode
and a modest amount of input and output capacitance.
The LTM8023 is a fixed frequency PWM regulator. The
switching frequency is set by simply connecting the
appropriate resistor value from the R T pin to GND.
An internal regulator provides power to the control cir-
cuitry. The bias regulator normally draws power from the
V IN pin, but if the BIAS pin is connected to an external
APPLICATIONS INFORMATION
For most applications, the design process is straight
forward, summarized as follows:
1. Look at Table 1 and find the row that has the desired
input range and output voltage.
2. Apply the recommended C IN , C OUT , R ADJ and R T values.
3. Connect BIAS as indicated.
While these component combinations have been tested for
proper operation, it is incumbent upon the user to verify
proper operation over the intended system’s line, load and
environmental conditions.
Capacitor Selection Considerations
The C IN and C OUT capacitor values in Table 1 are the
minimum recommended values for the associated oper-
ating conditions. Applying capacitor values below those
voltage higher than 2.8V, bias power will be drawn from
the external source (typically the regulated output volt-
age). This improves efficiency. The RUN/SS pin is used
to place the LTM8023 in shutdown, disconnecting the
output and reducing the input current to less than 1μA.
To further optimize efficiency, the LTM8023 automatically
switches to Burst Mode operation in light load situations.
Between bursts, all circuitry associated with controlling
the output switch is shut down reducing the input supply
current to 50μA in a typical application. The oscillator
reduces the LTM8023’s operating frequency when the volt-
age at the ADJ pin is low. This frequency foldback helps to
control the output current during start-up and overload.
The LTM8023 contains a power good comparator which
trips when the ADJ pin is at 92% of its regulated value.
The PGOOD output is an open-collector transistor that is
off when the output is in regulation, allowing an external
resistor to pull the PGOOD pin high. Power good is valid
when the LTM8023 is enabled and V IN is above 3.6V.
indicated in Table 1 is not recommended, and may result
in undesirable operation. Using larger values is generally
acceptable, and can yield improved dynamic response, if
it is necessary. Again, it is incumbent upon the user to
verify proper operation over the intended system’s line,
load and environmental conditions.
Ceramic capacitors are small, robust and have very low
ESR. However, not all ceramic capacitors are suitable.
X5R and X7R types are stable over temperature and ap-
plied voltage and give dependable service. Other types,
including Y5V and Z5U have very large temperature and
voltage coefficients of capacitance. In an application cir-
cuit they may have only a small fraction of their nominal
capacitance resulting in much higher output voltage ripple
than expected.
8023fi
For more information www.linear.com/LTM8023
9
相关PDF资料 |
PDF描述 |
|---|---|
| T95R157M020EZAL | CAP TANT 150UF 20V 20% 2824 |
| VI-J2N-IZ | CONVERTER MOD DC/DC 18.5V 25W |
| HBC35DRAI-S734 | CONN EDGECARD 70POS .100 R/A PCB |
| VE-JNF-CX-F4 | CONVERTER MOD DC/DC 72V 75W |
| VI-JNR-IZ | CONVERTER MOD DC/DC 7.5V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8023MPV | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A, 36V DC/DC μModule |
| LTM8023MPV#PBF | 功能描述:IC BUCK SYNC ADJ 2A 50LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:100V 电压 - 输入（最大）:200V Voltage - Output 1:7.5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM8023MPV#PBF | 制造商:Linear Technology 功能描述:DC/DC MICRO MODULE IC 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC POWER SUPPLY, LGA-50 |
| LTM8023MPV-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A, 36V DC/DC μModule |
| LTM8023MPY#PBF | 功能描述:IC DC/DC UMODULE 2A 50BGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。