- 您现在的位置：买卖IC网 > PDF目录16297 > LTM8061EV-8.4#PBF (Linear Technology)IC BATTERY CHARGER 8.4V 77-LGA PDF资料下载
参数资料
| 型号： | LTM8061EV-8.4#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY CHARGER 8.4V 77-LGA |
| 产品培训模块： | LTM806x Step-Down Micro-Module Battery Charger |
| 设计资源： | DC1645A Design Files |
| 特色产品： | μModule Products |
| 标准包装： | 170 |
| 系列： | µModule® |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.95 V ~ 32 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 77-BLGA |
| 供应商设备封装： | 77-LGA（15x9） |
| 包装： | 托盘 |
| 配用： | DC1645A-D-ND - BOARD EVAL LTM8061-8.4 |
LTM8061
PIN FUNCTIONS
GND (Bank 1): Power and Signal Ground Return.
BAT (Bank 2): Battery Charge Current Output Bus. The
charge function operates to achieve the final float voltage
at this pin. The auto-restart feature initiates a new charge
cycle when the voltage at the BAT pin falls 2.5% below
the float voltage. Once the charge cycle is terminated, the
input bias current of the BAT pin is reduced to minimize
battery discharge while the charger remains connected.
In most applications, connect BIAS to BAT.
V INA (Bank 3): Anode of Input Reverse Protection Schottky
Diode. Connect the input power here if input voltage pro-
tection is desired.
V INC /CLP (Bank 4): This pad bank connects to the cathode
of the input reverse protection diode. In addition, system
current levels can be monitored by connecting a sense
resistor from this pin to the V IN pin. Additional system
load is drawn from the V IN pin connection, and maximum
system load is achieved when V VINC/CLP – V VIN = 50mV. The
LTM8061 servos the charge current required to maintain
programmed maximum system current. If this function is
not desired, connect the V INC /CLP pin to the V IN pin (see
the Applications Information section). Do not raise this
pin above V IN + 0.5V.
V IN (Bank 5): Charger Input Supply. Apply C IN here. Con-
nect the input power here if no input power rectification
is required.
BIAS (Pin G7): The BIAS pin connects to the internal power
bus. Connect to a power source greater than 2.5V and
less than 10V. In most applications, connect BIAS to BAT.
CHRG (Pin K7): Open-Collector Charger Status Output.
Typically pulled up through a resistor to a reference volt-
age. This status pin can be pulled up to voltages as high
as V IN and can sink currents up to 10mA. During a battery
charge cycle, CHRG is pulled low. When the charge cycle
terminates, the CHRG pin becomes high impedance. If the
internal timer is used for termination, the pin stays low
during the charge cycle until the charge current drops below
a C/10 rate even though the charger will continue to top
off the battery until the end-of-charge timer terminates the
charge cycle. A temperature fault also causes this pin to
be pulled low (see the Applications Information section). If
RUN is low, or the LTM8061 is otherwise powered down,
the state of the CHRG pin is invalid.
NTC (Pin H6): Battery Temperature Monitor Pin. This pin
is the input to the NTC (negative temperature coefficient)
thermistor temperature monitoring circuit. This function is
enabled by connecting a 10kΩ, β = 3380 NTC thermistor
from the NTC pin to ground. The pin sources 50μA, and
monitors the voltage across the 10kΩ thermistor. When
the voltage on this pin is above 1.36V (T < 0°C) or below
0.29V (T > 40°C), charging is disabled and the CHRG and
FAULT pins are both pulled low. If internal timer termina-
tion is being used, the timer is paused, suspending the
charge cycle. Charging resumes when the voltage on NTC
returns to within the 0.29V to 1.36V active region. There
is approximately 5°C of temperature hysteresis associated
with each of the temperature thresholds. The temperature
monitoring function remains enabled while thermistor
resistance to ground is less than 250kΩ. If this function
is not desired, leave the NTC pin unconnected.
8061fa
For more information www.linear.com/LTM8601
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTM8061EV-8.2#PBF | IC BATTERY CHARGER 8.2V 77-LGA |
| M3CCA-2660K | IDC CABLE - MKC26A/MC26F/MKC26A |
| M1TXK-3436R | IDC CABLE - MSD34K/MC34M/X |
| VE-J1F-EZ-F4 | CONVERTER MOD DC/DC 72V 25W |
| M3AAK-3006J | IDC CABLE - MSC30K/MC34G/MSC30K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8061IV-4.1#PBF | 功能描述:IC BATTERY CHARGER 4.1V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTM8061IV-4.1PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061IV-4.2#PBF | 功能描述:IC BATTERY CHARGER 4.2V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTM8061IV-4.2PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061IV-8.2#PBF | 功能描述:IC BATTERY CHARGER 8.2V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。