- 您现在的位置：买卖IC网 > PDF目录16297 > LTM8061EV-8.4#PBF (Linear Technology)IC BATTERY CHARGER 8.4V 77-LGA PDF资料下载
参数资料
| 型号： | LTM8061EV-8.4#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/22页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY CHARGER 8.4V 77-LGA |
| 产品培训模块： | LTM806x Step-Down Micro-Module Battery Charger |
| 设计资源： | DC1645A Design Files |
| 特色产品： | μModule Products |
| 标准包装： | 170 |
| 系列： | µModule® |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.95 V ~ 32 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 77-BLGA |
| 供应商设备封装： | 77-LGA（15x9） |
| 包装： | 托盘 |
| 配用： | DC1645A-D-ND - BOARD EVAL LTM8061-8.4 |
LTM8061
PIN FUNCTIONS
RNG/SS (Pin H7): Charge Current Programming/Soft-
Start Pin. This pin allows the maximum charge current
to be reduced from the default 2A level, and can be used
to employ a soft-start function. This pin has an effective
range from 0V to 1V, with the maximum BAT charge cur-
rent determined by I BAT .
50μA is sourced from this pin, so the maximum charge
current can be programmed by connecting a resistor
(R RNG/SS ) from RNG/SS to ground, and the maximum
battery charge current is:
I BAT = 2A ? V RNG/SS
I BAT = 2A ? 50μA ? R RNG/SS
where R RNG/SS is less than or equal to 20k?. With the
RNG/SS pin left open, the charge current is 2A.
Soft-start functionality can be implemented by connect-
ing a capacitor (C RNG/SS ) from RNG/SS to ground, such
that the time required to charge the capacitor to 1V (full
charge current) is the desired soft-start interval (t SS ). With
no R RNG/SS resistor applied, this capacitor value follows
the relation:
C RNG/SS = 50μA ? t SS
The RNG/SS pin is pulled low during fault conditions,
allowing graceful recovery from faults should soft-start
functionality be implemented. Both the soft-start capaci-
tor and the programming resistor can be implemented in
parallel. All C/10 monitoring functions are disabled while
V RNG/SS is below 0.1V to accommodate long soft-start
intervals.
RNG/SS voltage can also be manipulated using an active
device, employing a pull-down transistor to disable charge
current or to dynamically servo maximum charge current.
Manipulation of the RNG/SS pin with active devices that
have low impedance pull-up capability is not allowed (see
the Applications Information section).
FAULT (Pin J7): Open-Collector Fault Status Output. Typi-
cally pulled up through a resistor to a reference voltage.
This status pin can be pulled up to voltages as high as
V IN , and can sink currents up to 10mA. This pin indicates
charge cycle fault conditions during a battery charge cycle.
A temperature fault causes this pin to be pulled low. If the
internal timer is used for termination, a bad battery fault
also causes this pin to be pulled low. If no fault condi-
tions exist, the FAULT pin remains high impedance (see
the Applications Information section). If RUN is low, or
the LTM8061 is otherwise powered down, the state of the
FAULT pin is invalid.
TMR (Pin J6): End-Of-Cycle Timer Programming Pin.
If a timer-based charge termination is desired, connect
a capacitor from this pin to ground. Full charge end-of
cycle time (in hours) is programmed with this capacitor
following the equation:
t EOC = C TIMER ? 4.4 ? 10 6
A bad battery fault is generated if the battery does not
reach the precondition threshold voltage within one-eighth
of t EOC , or:
t PRE = C TIMER ? 5.5 ? 10 5
A 0.68μF capacitor is typically used, which generates a
timer EOC of three hours, and a precondition limit time of
22.5 minutes. If a timer-based termination is not desired,
the timer function is disabled by connecting the TMR pin
to ground. With the timer function disabled, charging
terminates when the charge current drops below a C/10
rate, or I CHG(MAX) /10.
RUN (Pin K6): Precision Threshold Enable Pin. The RUN
threshold is 1.20V (rising), with 120mV of input hystere-
sis. When in shutdown mode, all charging functions are
disabled. The precision threshold allows use of the RUN
pin to incorporate UVLO functions. If the RUN pin is pulled
below 0.4V, the μModule enters a low current shutdown
mode where the V IN pin current is reduced to 15μA. Typical
RUN pin input bias current is 1μA. If the shutdown function
is not desired, connect the pin to the V IN pin.
8061fa
8
For more information www.linear.com/LTM8601
相关PDF资料 |
PDF描述 |
|---|---|
| LTM8061EV-8.2#PBF | IC BATTERY CHARGER 8.2V 77-LGA |
| M3CCA-2660K | IDC CABLE - MKC26A/MC26F/MKC26A |
| M1TXK-3436R | IDC CABLE - MSD34K/MC34M/X |
| VE-J1F-EZ-F4 | CONVERTER MOD DC/DC 72V 25W |
| M3AAK-3006J | IDC CABLE - MSC30K/MC34G/MSC30K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8061IV-4.1#PBF | 功能描述:IC BATTERY CHARGER 4.1V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTM8061IV-4.1PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061IV-4.2#PBF | 功能描述:IC BATTERY CHARGER 4.2V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTM8061IV-4.2PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061IV-8.2#PBF | 功能描述:IC BATTERY CHARGER 8.2V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。