- 您现在的位置：买卖IC网 > PDF目录61639 > LV5124T 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | LV5124T |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | 0.150 INCH, MSOP-8 |
| 文件页数： | 5/8页 |
| 文件大小： | 171K |
| 代理商： | LV5124T |
LV5124T
No.A1153-5/8
Functional Description
Over-charge detection
If either of the cell voltage is equal to or more than the over-charge detection voltage, stop further charging by
turning “L” the Cout pin and turning off external Nch MOS FET after the over-charge detection delay time.
This delay time is set by the internal counter.
The over-charge detection comparator has the hysteresis function. Note that this hysteresis can be cancelled by
connecting the load after detection of over-charge detection. and it becomes small to hysteresis peculiar to a
comparator.
Once over-charge detection is made, over-current detection is not made to prevent incorrect operations. Note that
short-circuit can be detected.
Over-charge release
If both cell voltages become equal to or less than the over-charge release voltage (VM
≤ Vd3) when charger is
connected, or if it become equal to or less than the over-charge release voltage (VM > Vd3) when load is connected,
the Cout pin returns to “H” after the over-charge release delay time set by the internal counter.
When load is connected and either cell or both cell voltages are equal to or more than the over-charge release voltage
([VM > Vd3, the Cout pin does not return to “H”. But the load current flows through the parasitic diode of external
Nch MOS FET on Cout, consequently each cell voltage becomes equal to or less than over-charge release voltage
(VM > Vd3), the Cout pin returns to “H” after the over-charge release delay time.
Over-discharge detection
When either cell voltage is equal to or less than over-discharge voltage, the IC stops further discharging by turning
the Dout pin “L” and turning off external Nch MOS FET after the over-charge detection delay time.
The IC goes into stand-by mode after detecting over-discharge and its consumption current is kept at about 0A. After
over-discharge detection, the V- pin will be connected to VDD pin via internal resistor (typ 200k).
Over-discharge release
Release from over-discharge is made by only connecting charger. If the V- pin voltage becomes equal to or lower
than the stand-by release voltage by connecting charger after detecting over-discharge, The IC is released from the
stand-by state to start cell voltage monitoring. If both cell voltages become equal to or more than the over-discharge
detection voltage by charging, the Dout pin returns to “H” after the over-discharge release delay time set by the
internal counter.
Over-current detection
When excessive current flows through the battery, the V- pin voltage rises by the ON resister of external MOS FET
and becomes equal to or more than the over-current detection voltage, the Dout pin turns to “L” after the over-current
detection delay time and the external Nch MOS FET is turned off to prevent excessive current in the circuit. The
detection delay time is set by the internal counter. After detection, the V- pin will be connected to VSS via internal
resistor (typ 1M). It will not go into stand-by mode after detecting over-current.
Short circuit detection
If greater discharging current flows through the battery and the V- pin voltage becomes equal to or more than the
short-circuit detection voltage, it will go into short-circuit detection state after the short circuit delay time shorter than
the over-current detection delay time. When short-circuit is detected, just like the time of over-current detection, the
Dout pin turns to “L” and external Nch MOS FET is turned off to prevent high current in the circuit. The V- pin will
be connected to VSS after detection via internal resistor (typ 1M). It will not go into stand-by mode after detecting
short circuit.
Over-current/short-detection release
After detecting over-current or short circuit, the internal resistor (typ.1M) between V- pin and VSS pin becomes
effective. In this case, the V-pin voltage will be more than over-current detection voltage because of the relation
between internal resister and the internal impedance of V- pin. Therefore, if the load resister is removed after
detecting over-current or short circuit, the detection state will be kept. Release from over-current or short circuit is
only made by connecting a charger to make the V- pins lower than over-current detection voltage and the Dout pin
returns to “H after over-current release delay time set by the internal counter.
相关PDF资料 |
PDF描述 |
|---|---|
| LV59018M | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LV8406T | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LVA5.25S | 1-OUTPUT 3 W DC-DC REG PWR SUPPLY MODULE |
| LVD5.25S | 1-OUTPUT 9 W DC-DC REG PWR SUPPLY MODULE |
| LVC5.25S | 1-OUTPUT 7 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV5124T-TLM-E | 制造商:ON Semiconductor 功能描述:2-CELL LIB PROTECTION - Tape and Reel |
| LV5125T-TLM-E | 制造商:ON Semiconductor 功能描述:2-CELL LIB PROTECTION - Tape and Reel |
| LV5207LP | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Cellular Phone LED Driver |
| LV5207LP-E | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LV5207LP-TE-L-E | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。