- 您现在的位置：买卖IC网 > PDF目录45001 > LV8414CS STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 PDF资料下载
参数资料
| 型号： | LV8414CS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 |
| 封装： | WLP-32 |
| 文件页数： | 14/36页 |
| 文件大小： | 451K |
| 代理商： | LV8414CS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LV8414CS
No.A1868-21/36
6. ENA pin function and I
2C serial data output enable setting
[ENA pin]
VCC consumption current during standby can be reduced to virtually zero by setting the ENA input pin to low.
Furthermore, when this pin is set to low, the output becomes OFF state (high-impedance), and the state of the internal
logic circuit is set to the initial excitation position (initial position).
By setting the ENA pin to high, the output becomes ON state, and the circuit operates from the initial excitation position.
* The output does not operate unless “output enable” is set to the “output ON” state using an I2C serial data
communication.
[I2C serial data output enable setting]
When “output enable” is set to the “output OFF” state, the output is placed in the high-impedance state at the rising edge
of the 8th SCL bit in the data transmission.
However, since the internal logic circuit is activated, the position number advances if CLK has been input. This means
that when “output enable” is set to the “output ON” state after this, the output is set to ON at the rising edge of the 8th
SCL bit in the data transmission, and that the output level at this time will be the level at the number to which the position
has advanced by the CLK input.
CLK1
(CLK2)
ENA
Output ON
Output OFF
I2C serial data communication enabled
High-impedance state
Internal initial position
100%
-100%
0%
I1
I2
相关PDF资料 |
PDF描述 |
|---|---|
| LV8481CS | STEPPER MOTOR CONTROLLER, PBGA10 |
| LV8731V | STEPPER MOTOR CONTROLLER, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8746V | STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8414CS_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Microstep Driver Motor Driver IC |
| LV8414CS-N-TE-L-H | 制造商:ON Semiconductor 功能描述:STEPPING MOTOR DRIVER - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / STEPPING MOTOR DRIVER |
| LV8414CS-TE-L-H | 功能描述:马达/运动/点火控制器和驱动器 MICROSTEP MOTOR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8415CB | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Blurring correction driver IC for DSC H bridge x 2ch driver |
| LV8415CB_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Blurring correction driver IC for DSC H bridge ?? 2ch driver |
发布紧急采购，3分钟左右您将得到回复。