- 您现在的位置：买卖IC网 > PDF目录45001 > LV8414CS STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 PDF资料下载
参数资料
| 型号： | LV8414CS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 |
| 封装： | WLP-32 |
| 文件页数： | 28/36页 |
| 文件大小： | 451K |
| 代理商： | LV8414CS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页
LV8414CS
No.A1868-34/36
12. Current control operation specification
[Sine wave increasing direction]
[Description of current limiting operation]
In each current mode, the operation sequence is as described below :
At rise of chopping frequency, the CHARGE mode begins.
The coil current (ICOIL) and setting current (IREF) are compared in the forced CHARGE section.
When (ICOIL
< IREF) existed in the forced CHARGE section:
The CHARGE mode is established until ICOIL
≥ IREF. Then it is switched to the SLOW DECAY mode,
and finally it is switched to the FAST DECAY mode.
When (ICOIL
< IREF) did not exist in the forced CHARGE section:
The FAST DECAY mode begins. The coil current is attenuated in the FAST DECAY mode till one
cycle of chopping is over.
Above operations are repeated. Normally, the SLOW (+FAST) DECAY mode continues in the sine wave increasing
direction, then entering the FAST DECAY mode till the current is attenuated to the set level and followed by the SLOW
DECAY mode.
(Charge mode)
(Slow decay mode)
(Fast decay mode)
FAST
SLOW
CHARGE
FAST
SLOW
CHARGE
Current mode
fchop
(Initial state:
400kHz)
Coil current
CLK
Set current
Forced
CHARGE
section
FAST
SLOW
FAST
SLOW
CHARGE
Current mode
fchop
(Initial state:
400kHz)
Coil current
CLK
Set current
Forced
CHARGE
section
Forced CHARGE
section
CHARGE
VM
ON
OFF
ON
VM
ON
OFF
ON
VM
OFF
ON
OFF
ON
相关PDF资料 |
PDF描述 |
|---|---|
| LV8481CS | STEPPER MOTOR CONTROLLER, PBGA10 |
| LV8731V | STEPPER MOTOR CONTROLLER, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8743V | 0.8 A SWITCHING CONTROLLER, 440 kHz SWITCHING FREQ-MAX, PDSO44 |
| LV8746V | STEPPER MOTOR CONTROLLER, 1.2 A, PDSO44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8414CS_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Microstep Driver Motor Driver IC |
| LV8414CS-N-TE-L-H | 制造商:ON Semiconductor 功能描述:STEPPING MOTOR DRIVER - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / STEPPING MOTOR DRIVER |
| LV8414CS-TE-L-H | 功能描述:马达/运动/点火控制器和驱动器 MICROSTEP MOTOR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8415CB | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Blurring correction driver IC for DSC H bridge x 2ch driver |
| LV8415CB_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Blurring correction driver IC for DSC H bridge ?? 2ch driver |
发布紧急采购，3分钟左右您将得到回复。