- 您现在的位置：买卖IC网 > PDF目录98003 > LV8713T (SANYO SEMICONDUCTOR CO LTD) STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF资料下载
参数资料
| 型号： | LV8713T |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封装： | 0.225 INCH, TSSOP-24 |
| 文件页数： | 7/16页 |
| 文件大小： | 304K |
| 代理商： | LV8713T |
LV8713T
No.A1918-15/16
(13) Current control timing chart(Chopping operation)
(Sine wave increasing direction)
(Sine wave decreasing direction)
In each current mode, the operation sequence is as described below :
At rise of chopping frequency, the CHARGE mode begins. (The Blanking section in which the CHARGE mode is
forced regardless of the magnitude of the coil current (ICOIL) and set current (IREF) exists for 1
μs.)
The coil current (ICOIL) and set current (IREF) are compared in this blanking time.
When (ICOIL < IREF) state exists ;
The CHARGE mode up to ICOIL
≥ IREF, then followed by changeover to the SLOW DECAY mode, and
finally by the FAST DECAY mode for approximately 1
μs.
When (ICOIL < IREF) state does not exist ;
The FAST DECAY mode begins. The coil current is attenuated in the FAST DECAY mode till one cycle of
chopping is over.
Above operations are repeated. Normally, the SLOW (+FAST) DECAY mode continues in the sine wave increasing
direction, then entering the FAST DECAY mode till the current is attenuated to the set level and followed by the SLOW
DECAY mode.
FAST
SLOW
CHARGE
FAST
SLOW
CHARGE
Current mode
fchop
Coil current
STEP
Set current
FAST
SLOW
FAST
SLOW
CHARGE
Current mode
fchop
Coil current
STEP
Set current
Forced CHARGE
section
CHARGE
Chopping cycle
BLANKING section
Chopping cycle
相关PDF资料 |
PDF描述 |
|---|---|
| LV8741V | STEPPER MOTOR CONTROLLER, 1.75 A, PDSO44 |
| LV8760T | BRUSH DC MOTOR CONTROLLER, 4 A, PDSO20 |
| LV8761V | BRUSH DC MOTOR CONTROLLER, 4 A, PDSO36 |
| LW006F-LP | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| LW006A-LP | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8713TGEVB | 功能描述:电源管理IC开发工具 EVM FOR LV8713T RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LV8713T-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8713T-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 4-16V Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8727 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Current Control Stepping Motor Driver |
| LV8727-E | 功能描述:马达/运动/点火控制器和驱动器 PRINTER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。