- 您现在的位置：买卖IC网 > PDF目录149382 > LX1554ID-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO14 PDF资料下载
参数资料
| 型号： | LX1554ID-TR |
| 厂商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分类： | 稳压器 |
| 英文描述： | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封装： | ROHS COMPLIANT, PLASTIC, SOIC-14 |
| 文件页数： | 7/18页 |
| 文件大小： | 483K |
| 代理商： | LX1554ID-TR |
ULTRA-LOW START-UP CURRENT, CURRENT-MODE PWM
LX1552/3/4/5
PRODUCT D A T ABOOK 1996/1997
15
Copyright 1994
Rev. 1.0b
P RODUCTION
D ATA
S HEET
THEO R Y OF OPER A TION
CURRENT SENSE COMPARATOR AND PWM LATCH
Switch current is sensed by an external sense resistor (or a current
transformer), monitored by the C.S. pin and compared internally
with voltage from error amplifier output. The comparator output
resets the PWM latch ensuring that a single pulse appears at the
output for any given oscillator cycle. The LX1554/55 series has
an additional flip flop stage that limits the output to less than 50%
duty cycle range as well as dividing its output frequency to half
of the oscillator frequency.
The current sense comparator
threshold is internally clamped to 1V nominally which would
limit peak switch current to:
Equation 1 is used to calculate the value of sense resistor during
the current limit condition where switch current reaches its
maximum level.
In normal operation of the converter, the
relationship between peak switch current and error voltage
(voltage at pin 1) is given by:
The above equation is plotted in Figure 29. Notice that the gain
becomes non-linear above current sense voltages greater than
≈
0.95 volts. It is therefore recommended to operate below this
range during normal operation. This would insure that the overall
closed loop gain of the system will not be affected by the change
in the gain of the current sense stage.
0
0.4
Error Amplifier Output Voltage - (V)
Current
Sense
Threshold
-
(V)
0.2
0.5
0.1
0.6
0.7
0.3
0
0.5 1.0 1.5 2.0
2.5 3.0 3.5
5.0
1.0
0.8
0.9
4.0 4.5
T
A = 25°C
1.1
T
A = 125°C
T
A = -55°C
FIGURE 29 — CURRENT SENSE THRESHOLD vs. ERROR AMPLIFIER OUTPUT
ERROR AMPLIFIER
The error amplifier has a PNP input differential stage with access
to the Inverting input and the output pin.
The N.I. input is
internally biased to 2.5 volts and is not available for any external
connections. The maximum input bias current for the LX155XC
series is 0.5A, while LX155XI/155XM devices are rated for 1A
maximum over their specified range of ambient temperature.
Low value resistor dividers should be used in order to avoid
output voltage errors caused by the input bias current. The error
amplifier can source 0.5mA and sink 2mA of current. A minimum
feedback resistor (R
F) value of is given by:
OUTPUT STAGE
The output section has been specifically designed for direct drive
of power MOSFETs. It has a totempole configuration which is
capable of high peak current for fast charging and discharging of
external MOSFET gate capacitance. This typically results in a rise
and fall time of 50ns for a 1000pf capacitive load. Each output
transistor (source and sink) is capable of supplying 200mA of
continuous current with typical saturation voltages versus tem-
perature as shown in Figures 21 & 22 of the characteristic curve
section. All devices are designed to minimize the amount of
shoot-thru current which is a result of momentary overlap of
output transistors. This allows more efficient usage of the IC at
higher frequencies, as well as improving the noise susceptibility
of the device. Internal circuitry insures that the outputs are held
off during V
CC ramp-up. Figure 20, in the characteristic curves
section, shows output sink saturation voltage vs. current at 5V.
V
Z
R
S
(1) I
SP =
where:
I
SP ≡ Peak switch current
V
Z ≡ internal zener
0.9V
≤ V
Z ≤ 1.1V
(1) I
SP =
where:
V
E ≡ Voltage at pin 1
V
F ≡ Diode - Forward voltage
0.7V at T
A = 25°C
V
E - 2VF
3 * R
S
R
FMIN =
≈ 10K
3(1.1) + 1.8
0.5mA
相关PDF资料 |
PDF描述 |
|---|---|
| L6230QTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| LM4040AIM-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LM329BZX | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, PBCY3 |
| L6122 | 3-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP20 |
| LM1001-7EPD1AF | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1554IM | 功能描述:IC REG CTRLR BST FLYBK ISO 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LX1554MY | 功能描述:IC REG CTRLR BST FLYBK ISO 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LX1555 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:ULTRA-LOW START-UP CURRENT, CURRENT-MODE PWM |
| LX1555CD | 功能描述:IC REG CTRLR PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LX1555CDM | 功能描述:IC REG CTRLR BST FLYBK ISO 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。