- 您现在的位置：买卖IC网 > PDF目录45008 > LX1742CDU-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) SWITCHING REGULATOR, PDSO8 PDF资料下载
参数资料
| 型号： | LX1742CDU-TR |
| 厂商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO8 |
| 封装： | PLASTIC, MSOP-8 |
| 文件页数： | 12/13页 |
| 文件大小： | 456K |
| 代理商： | LX1742CDU-TR |
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 8
Copyright
2000
Rev. 1.0b, 2005-03-03
WWW
.Microse
m
i
.CO
M
LX1742
High Efficiency High Voltage Boost Controller
PRODUCTION DATA SHEET
I N T E GRA T ED
PR ODUC T S
EVALUATI ON BOA RD
OVERVIEW
The LXE1742 evaluation board is available from
Microsemi for assessing overall circuit performance. The
evaluation board, shown in Figure 5, is 3 by 3 inches (i.e.,
7.6 X 7.6cm) square and factory calibrated to provide a
nominal 18V output from a 1.6V to 6.0V input. Circuit
designers can easily modify the output voltage and peak
current to suit their particular application by adjusting the
R2, R3, and R4 values accordingly.
Further, other
components are easily swapped out to promote design
verification of any particular circuit application. Table 1
describes the evaluation board’s electrical interface.
ELECTRICAL CONNECTIONS
The system level DC input voltage is applied to VIN.
Connect the test load to VOUT. The Vin & GND terminal
at J4 provides easy test point access. A similar connection is
available for monitoring the output voltage via J5. The
output voltage is adjusted by selecting appropriate values for
R3 and R24. Further adjustment of the output voltage is
achieved by applying either a DC voltage or a PWM-type
signal to the ADJ input (J4).
The evaluation board accommodates both low frequency
(f < 100KHz) and high frequency (f > 100KHz) PWM
signals by connecting either JU1 or JU4 jumper position
respectively. The ADJ pin is easily grounded for fixed
voltage applications by inserting a jumper into the JU5
position. Table 2 provides a complete list of all jumper
positions.
Removing the jumper from the /SHDN position disables
the LX1742 by disconnecting pin 4 from VIN. The load is
still capable of drawing current through the inductor & diode
circuit path when the IC is in shutdown mode. Hence,
VOUT during shutdown will be approximately VIN minus
the inductor and diode forward voltage drop.
The LX1742 can achieve output voltages up to 25V. In
certain applications, it is necessary to protect the load from
excessive voltage excursions.
The evaluation board
provides a zener clamp diode (D1) for this purpose.
The LXE1742 evaluation board offers a cost effective
solution for evaluation of the LX1742. Table 3 provides the
factory installed component list for the evaluation board and
the board schematic is shown in Figure 4.
Table 1: Input and Output Pin Assignments
Name
Application
Range
Description
VIN
0 to 6V
Main power supply input for evaluation board
Vin (J4)
0 to 6V
Connected to VIN (Alternate position or test point)
SHDN (J4)
0 to VIN
Pulled up to VCC on board (10K), Ground to inhibit the LX1742.
ADJ (J4)
0 to VIN-
100mV
Apply a DC input or PWM input to adjust the output voltage (note: see figure 9).
GND (J4)
0V
Circuit ground
GND
0V
Additional circuit ground connection point.
FDBK
0 to VIN
Apply a DC input or PWM input to adjust the output voltage.
GND2
0V
Additional circuit ground connection point.
VOUT
VIN to 25V
Output voltage test point. Programmed for 18V output, adjustable up to 25V.
SWITCH
N/A
Test point for lX1742 pin 1.
/SHDN
0 to VIN
A DC voltage above (below) 1.6V (0.4V) enables (disables) the LX172
Note: All pins are referenced to ground.
EE
VV
AA
LL
UU
AA
TT
IIOO
NN
BB
OO
AA
RR
DD
相关PDF资料 |
PDF描述 |
|---|---|
| LX1823IQ | 2 A SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC20 |
| LX1823IN | 2 A SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDIP16 |
| LX1823IJ | 2 A SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, CDIP16 |
| LX1823IJ | 2 A SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, CDIP16 |
| LX1823MJ | 2 A SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, CDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1742EVALKIT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC:DC Converter |
| LX1744 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:Dual Output Boost ? LED Driver / LCD Bias |
| LX1744 EVAL KIT | 制造商:Microsemi Corporation 功能描述:LED BACKLIGHT CONTROLLERS AND DRIVERS - Bulk |
| LX1744CLQ | 功能描述:IC LED DRVR WT/CLR BCKLGT 16MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| LX1744CPW | 功能描述:IC LED DRVR WT/CLR BCKLT 14TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。