参数资料
型号: LXT360PE
英文描述: PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC
中文描述: 的PCM收发器|单|优税PCM-30/E-1 |的CMOS | LDCC | 28脚|塑料
文件页数: 23/52页
文件大小: 1187K
代理商: LXT360PE
Integrated T1/E1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications
LXT361
Datasheet
23
ZEROV detection is enabled when the HDB3 encoders/decoders are enabled. This requires
CR1.ENCENB = 1, also CR1.EC4:1 = 100x or 1010, which establishes E1 operation. To select
ZEROV detection, set bit CR4.ZEROV = 1.
3.5.4
Alarm Condition Monitoring
3.5.4.1
Loss of Signal
The LXT361 Loss of Signal (LOS) monitor function is compatible with ITU G.775 and ETSI
300233. The receiver LOS monitor loads a digital counter at the RCLK frequency. The count
increments with each received 0 and the counter resets to 0 on receipt of a 1. When the count
reaches
n
0s, bit PSR.LOS is set to
1
, and the MCLK replaces the recovered clock at the RCLK
output in a smooth transition. For T1 operations, the number of 0s, n = 175, and for E1 operations,
n = 32. For both T1 and E1 operation,
n
can be set to 2048 by setting bit CR4.LOS2048 = 1.
For T1 operation, when the received signal has 12.5% 1s (16 marks in a sliding 128-bit period, with
fewer than 100 consecutive 0s), bit PSR.LOS = 0 and the recovered clock replaces MCLK at the
RCLK output in another smooth transition.
For E1 operation, the LOS condition is cleared when the received signal has 12.5% 1s density (four
1s in a sliding 32-bit window with fewer than 16 consecutive 0s). In E1 operation, the out-of-LOS
criterion can be modified from 12.5% marks density to 32 consecutive marks by setting bit
CR4.COL32CM = 1.
During LOS, the device sends received data to the RPOS/RNEG pins (or RDATA in Unipolar
mode). Bit PSR.LOS = 1 to indicate LOS condition, and can generate an interrupt to the host
controller if so programmed.
3.5.4.2
Alarm Indication Signal Detection
The receiver detects an AIS pattern when it receives fewer than three 0s in any string of 2048 bits.
The device clears the AIS condition when it receives three or more 0s in a string of 2048 bits.
The AIS bit in the Performance Status Register indicates AIS detection. Whenever the AIS status
changes, bit TSR.TAIS =1. Unless masked, a change of AIS status generates an interrupt.
3.5.4.3
Driver Failure Open Mode
The DFM Open (DFMO) bit is available in the Performance Status Register to indicate an open
condition on the lines. DFMO can generate an INT to the host controller. The Transition Status
Register bit TDFMO indicates a transition in the status of the bit. Writing a 1 to ICR.CDFMO will
clear or mask the interrupt.
3.5.4.4
Elastic Store Overflow/Underflow
When the bit count in the Elastic Store (ES) is within two bits of overflowing or underflowing the
ES adjusts the output clock by
1
/
8
of a bit period. The ES provides an indication of overflow and
underflow via bits TRS.ESOVR and TSR.ESUNF. These are sticky bits and will stay set to 1 until
the host controller reads the register. These interrupts can be cleared or masked by writing a 1 to the
bits ICR.CESO and ICR.CESU, respectively.
相关PDF资料
PDF描述
LXT384BE Telecomm/Datacomm
LXT384LE Telecomm/Datacomm
LXT386BE PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC
LXT386LE PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC
LXT388LE PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC
相关代理商/技术参数
参数描述
LXT360QE 制造商:Intel 功能描述: 制造商:LEVEL ONE 功能描述:
LXT361 制造商:LVL1 制造商全称:LVL1 功能描述:Integrated T1/E1 LH/SH Transceivers for DS1/DSX-1/CSU or NTU/ISDN PRI Applications
LXT361LE 制造商:LEVEL ONE 功能描述:361LE
LXT361PE 制造商:LEVEL 1 功能描述: 制造商:LEVEL ONE 功能描述: 制造商:Intel 功能描述:PCM TRANSCEIVER, Single, CEPT PCM-30/E-1, 28 Pin, Plastic, PLCC
LXT361QE 制造商:LEVEL ONE 功能描述: 制造商:LEVEL ONE 功能描述:DATACOM, PCM TRANSCEIVER, PQFP44