- 您现在的位置：买卖IC网 > PDF目录180109 > M27C800-70M1 (STMICROELECTRONICS) 512K X 16 OTPROM, 70 ns, PDSO44 PDF资料下载
参数资料
| 型号： | M27C800-70M1 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 512K X 16 OTPROM, 70 ns, PDSO44 |
| 封装： | 0.525 INCH, PLASTIC, SO-44 |
| 文件页数： | 16/18页 |
| 文件大小： | 171K |
| 代理商： | M27C800-70M1 |
7/18
M27C800
Figure 5. Word-Wide Read Mode AC Waveforms
Note: BYTEVPP =VIH.
AI01596B
tAXQX
tEHQZ
A0-A18
E
G
Q0-Q15
tAVQV
tGHQZ
tGLQV
tELQV
VALID
Hi-Z
VALID
Two Line Output Control
Because EPROMs are usually used in larger
memory arrays, this product features a 2-line con-
trol function which accommodates the use of mul-
tiple memory connection. The two-line control
function
allows:
a. the lowest possible memory power dissipation
b. complete assurance that output bus contention
will not occur.
For the most efficient use of these two control
lines, E should be decoded and used as the prima-
ry device selecting function, while G should be
made a common connection to all devices in the
array and connected to the READ line from the
system control bus. This ensures that all deselect-
ed memory devices are in their low power standby
mode and that the output pins are only active
when data is required from a particular memory
device.
System Considerations
The power switching characteristics of Advanced
CMOS EPROMs require careful decoupling of the
supplies to the devices. The supply current ICC
has three segments of importance to the system
designer: the standby current, the active current
and the transient peaks that are produced by the
falling and rising edges of E.
The magnitude of the transient current peaks is
dependent on the capacitive and inductive loading
of the device outputs. The associated transient
voltage peaks can be suppressed by complying
with the two line output control and by properly se-
lected decoupling capacitors. It is recommended
that a 0.1F ceramic capacitor is used on every
device between VCC and VSS.
This should be a high frequency type of low inher-
ent inductance and should be placed as close as
possible to the device. In addition, a 4.7F electro-
lytic capacitor should be used between VCC and
VSS for every eight devices. This capacitor should
be mounted near the power supply connection
point. The purpose of this capacitor is to overcome
the voltage drop caused by the inductive effects of
PCB traces.
相关PDF资料 |
PDF描述 |
|---|---|
| M27C801-70B6X | 1M X 8 OTPROM, 70 ns, PDIP32 |
| M27V102-90B6 | 64K X 16 OTPROM, 90 ns, PDIP40 |
| M27V256-100B1TR | 256 Kbit 32Kb x 8 Low Voltage UV EPROM and OTP EPROM |
| M27V256-100B6TR | 256 Kbit 32Kb x 8 Low Voltage UV EPROM and OTP EPROM |
| M28840/19AD1P3 | 31 CONTACT(S), ALUMINUM, MALE, CIRCULAR ADAPTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M27C801-100B1 | 功能描述:可擦除可编程ROM 8M (1Mx8) 100ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| M27C801-100B1 | 制造商:STMicroelectronics 功能描述:PROM OTP CMOS 8MB 27C801 DIP32 |
| M27C801-100F1 | 功能描述:可擦除可编程ROM 8M (1Mx8) 100ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| M27C801-100F1 | 制造商:STMicroelectronics 功能描述:IC EPROM CMOS 8MB 27C801 DIP32 |
| M27C801-100F6 | 功能描述:可擦除可编程ROM 8M (1Mx8) 100ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
发布紧急采购，3分钟左右您将得到回复。