参数资料
型号: M28W160ECB85N1S
厂商: 意法半导体
英文描述: 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
中文描述: 16兆位(1兆x16插槽,引导块)3V电源快闪记忆体
文件页数: 11/50页
文件大小: 860K
代理商: M28W160ECB85N1S
11/50
M28W160ECT, M28W160ECB
COMMAND INTERFACE
All Bus Write operations to the memory are inter-
preted by the Command Interface. Commands
consist of one or more sequential Bus Write oper-
ations. An internal Program/Erase Controller han-
dles all timings and verifies the correct execution
of the Program and Erase commands. The Pro-
gram/Erase Controller provides a Status Register
whose output may be read at any time during, to
monitor the progress of the operation, or the Pro-
gram/Erase states. See
APPENDIX D.
,
Table 31.
,
Write State Machine Current/Next,
for a summary
of the Command Interface.
The Command Interface is reset to Read mode
when power is first applied, when exiting from Re-
set or whenever V
DD
is lower than V
LKO
. Com-
mand sequences must be followed exactly. Any
invalid combination of commands will reset the de-
vice to Read mode. Refer to
Table 3., Commands
,
in conjunction with the text descriptions below.
Read Memory Array Command
The Read command returns the memory to its
Read mode. One Bus Write cycle is required to is-
sue the Read Memory Array command and return
the memory to Read mode. Subsequent read op-
erations will read the addressed location and out-
put the data. When a device Reset occurs, the
memory defaults to Read mode.
Read Status Register Command
The Status Register indicates when a program or
erase operation is complete and the success or
failure of the operation itself. Issue a Read Status
Register command to read the Status Register’s
contents. Subsequent Bus Read operations read
the Status Register at any address, until another
command is issued. See
Table 10., Status Regis-
ter Bits
, for details on the definitions of the bits.
The Read Status Register command may be is-
sued at any time, even during a Program/Erase
operation. Any Read attempt during a Program/
Erase operation will automatically output the con-
tent of the Status Register.
Read Electronic Signature Command
The Read Electronic Signature command reads
the Manufacturer and Device Codes and the Block
Locking Status, or the Protection Register.
The Read Electronic Signature command consists
of one write cycle, a subsequent read will output
the Manufacturer Code, the Device Code, the
Block Lock and Lock-Down Status, or the Protec-
tion and Lock Register. See Tables
4
,
5
and
6
for
the valid address.
Read CFI Query Command
The Read Query Command is used to read data
from the Common Flash Interface (CFI) Memory
Area, allowing programming equipment or appli-
cations to automatically match their interface to
the characteristics of the device. One Bus Write
cycle is required to issue the Read Query Com-
mand. Once the command is issued subsequent
Bus Read operations read from the Common
Flash Interface Memory Area. See
APPENDIX
B., COMMON FLASH INTERFACE (CFI)
, Tables
25
,
26
,
27
,
28
,
29
and
30
for details on the infor-
mation contained in the Common Flash Interface
memory area.
Block Erase Command
The Block Erase command can be used to erase
a block. It sets all the bits within the selected block
to ’1’. All previous data in the block is lost. If the
block is protected then the Erase operation will
abort, the data in the block will not be changed and
the Status Register will output the error.
Two Bus Write cycles are required to issue the
command.
The first bus cycle sets up the Erase
command.
The second latches the block address in the
internal state machine and starts the Program/
Erase Controller.
If the second bus cycle is not Write Erase Confirm
(D0h), Status Register bits b4 and b5 are set and
the command aborts.
Erase aborts if Reset turns to V
IL
. As data integrity
cannot be guaranteed when the Erase operation is
aborted, the block must be erased again.
During Erase operations the memory will accept
the Read Status Register command and the Pro-
gram/Erase Suspend command, all other com-
mands will be ignored. Typical Erase times are
given in
Table 7., Program, Erase Times and Pro-
gram/Erase Endurance Cycles
.
See
APPENDIX C.
,
Figure 20., Erase Flowchart
and Pseudo Code
, for a suggested flowchart for
using the Erase command.
Program Command
The memory array can be programmed word-by-
word. Two bus write cycles are required to issue
the Program Command.
The first bus cycle sets up the Program
command.
The second latches the Address and the Data
to be written and starts the Program/Erase
Controller.
During Program operations the memory will ac-
cept the Read Status Register command and the
Program/Erase Suspend command. Typical Pro-
gram times are given in
Table 7., Program, Erase
Times and Program/Erase Endurance Cycles
.
相关PDF资料
PDF描述
M28W160ECB85N1T 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6E 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6F 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6S 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6T 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
相关代理商/技术参数
参数描述
M28W160ECB85N1T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N1U 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6E 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory
M28W160ECB85N6F 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory