- 您现在的位置：买卖IC网 > PDF目录296349 > M29W400BT70M6T (NUMONYX) 256K X 16 FLASH 2.7V PROM, 70 ns, PDSO44 PDF资料下载
参数资料
| 型号： | M29W400BT70M6T |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 256K X 16 FLASH 2.7V PROM, 70 ns, PDSO44 |
| 封装： | 0.525 INCH, PLASTIC, SOP-44 |
| 文件页数： | 2/26页 |
| 文件大小： | 313K |
| 代理商： | M29W400BT70M6T |
M29W400BT, M29W400BB
10/25
Erase Suspend Command. The Erase Suspend
Command may be used to temporarily suspend a
Block Erase operation and return the memory to
Read mode. The command requires one Bus
Write operation.
The Program/Erase Controller will suspend within
15s of the Erase Suspend Command being is-
sued. Once the Program/Erase Controller has
stopped the memory will be set to Read mode and
the Erase will be suspended. If the Erase Suspend
command is issued during the period when the
memory is waiting for an additional block (before
the Program/Erase Controller starts) then the
Erase is suspended immediately and will start im-
mediately when the Erase Resume Command is
issued. It will not be possible to select any further
blocks for erasure after the Erase Resume.
During Erase Suspend it is possible to Read and
Program cells in blocks that are not being erased;
both Read and Program operations behave as
normal on these blocks. Reading from blocks that
are being erased will output the Status Register. It
is also possible to enter the Auto Select mode: the
memory will behave as in the Auto Select mode on
all blocks until a Read/Reset command returns the
memory to Erase Suspend mode.
Erase Resume Command. The Erase Resume
command must be used to restart the Program/
Erase Controller from Erase Suspend. An erase
can be suspended and resumed more than once.
Table 9. Program, Erase Times and Program, Erase Endurance Cycles
(TA = 0 to 70°C or –40 to 85°C)
Note: 1. TA =25°C, VCC =3.3V.
Parameter
Min
Typ (1)
Typical after
100k W/E Cycles (1)
Max
Unit
Chip Erase (All bits in the memory set to ‘0’)
2.5
sec
Chip Erase
6
35
sec
Block Erase (64 Kbytes)
0.8
6
sec
Program (Byte or Word)
10
200
s
Chip Program (Byte by Byte)
5.5
30
sec
Chip Program (Word by Word)
2.8
15
sec
Program/Erase Cycles (per Block)
100,000
cycles
相关PDF资料 |
PDF描述 |
|---|---|
| M29W640GB70ZA6F | 4M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| M2Y51264TU88A2G-37B | 64M X 64 DDR DRAM MODULE, 0.5 ns, DMA240 |
| M30-1201100 | 22 CONTACT(S), FEMALE, TWO PART BOARD CONNECTOR, CRIMP |
| M30-6000206R | 2 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| M30-6000306R | 3 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M29W400BT70N1 | 功能描述:闪存 512Kx8 or 256Kx16 70 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29W400BT70N6 | 功能描述:闪存 512Kx8 or 256Kx16 70 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29W400BT90M1 | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29W400BT90M1T | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29W400BT90N1 | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。