参数资料
型号: M306N5FCVGP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
封装: 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件页数: 11/63页
文件大小: 825K
代理商: M306N5FCVGP
Usage precaution
Mitsubishi microcomputers
M16C / 62M (80-pin version) Group
(Low voltage version)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
Timer A (timer mode)
Usage Precaution
Timer A (event counter mode)
(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16” by underflow
or “000016” by overflow. Reading the timer Ai register after setting a value in the timer Ai register with
a count halted but before the counter starts counting gets a proper value.
(2) When stop counting in free run type, set timer again.
(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16”. Reading the
timer Ai register after setting a value in the timer Ai register with a count halted but before the counter
starts counting gets a proper value.
(1) Setting the count start flag to “0” while a count is in progress causes as follows:
The counter stops counting and a content of reload register is reloaded.
The TAiOUT pin outputs “L” level.
The interrupt request generated and the timer Ai interrupt request bit goes to “1”.
(2) The timer Ai interrupt request bit goes to “1” if the timer's operation mode is set using any of the
following procedures:
Selecting one-shot timer mode after reset.
Changing operation mode from timer mode to one-shot timer mode.
Changing operation mode from event counter mode to one-shot timer mode.
Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”
after the above listed changes have been made.
Timer A (one-shot timer mode)
(1) The timer Ai interrupt request bit becomes “1” if setting operation mode of the timer in compliance with
any of the following procedures:
Selecting PWM mode after reset.
Changing operation mode from timer mode to PWM mode.
Changing operation mode from event counter mode to PWM mode.
Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”
after the above listed changes have been made.
(2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop
counting. If the TAiOUT pin is outputting an “H” level in this instance, the output level goes to “L”, and
the timer Ai interrupt request bit goes to “1”. If the TAiOUT pin is outputting an “L” level in this instance,
the level does not change, and the timer Ai interrupt request bit does not becomes “1”.
Timer A (pulse width modulation mode)
Timer B (timer mode, event counter mode)
(1) Reading the timer Bi register while a count is in progress allows reading , with arbitrary timing, the
value of the counter. Reading the timer Bi register with the reload timing gets “FFFF16”. Reading the
timer Bi register after setting a value in the timer Bi register with a count halted but before the counter
starts counting gets a proper value.
相关PDF资料
PDF描述
M306N5MCT-XXXGP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
M306V0ME-XXXFP 16-BIT, MROM, MICROCONTROLLER, PQFP100
M306V0EEFP 16-BIT, OTPROM, MICROCONTROLLER, PQFP100
M306V2ME-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100
M306V2EEFP 16-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
M306N5MCT-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU
M306N5MCT-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU
M306N5MCV-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU
M306N5MCV-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU
M306N5MC-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU