- 您现在的位置：买卖IC网 > PDF目录69010 > M306N5FCVGP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M306N5FCVGP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 13/63页 |
| 文件大小： | 825K |
| 代理商： | M306N5FCVGP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
Usage precaution
Mitsubishi microcomputers
M16C / 62M (80-pin version) Group
(Low voltage version)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
17
Stop Mode and Wait Mode
A-D Converter
(1) If changing the measurement mode select bit is set after a count is started, the timer Bi interrupt
request bit goes to “1”.
(2) When the first effective edge is input after a count is started, an indeterminate value is transferred to
the reload register. At this time, timer Bi interrupt request is not generated.
Timer B (pulse period/pulse width measurement mode)
Interrupts
(1) Write to each bit (except bit 6) of A-D control register 0, to each bit of A-D control register 1, and to bit
0 of A-D control register 2 when A-D conversion is stopped (before a trigger occurs).
In particular, when the Vref connection bit is changed from “0” to “1”, start A-D conversion after an
elapse of 1
s or longer.
(2) When changing A-D operation mode, select analog input pin again.
(3) Using one-shot mode or single sweep mode
Read the correspondence A-D register after confirming A-D conversion is finished. (It is known by A-
D conversion interrupt request bit.)
(4) Using repeat mode, repeat sweep mode 0 or repeat sweep mode 1
Use the undivided main clock as the internal CPU clock.
(1) Reading address 0000016
When maskable interrupt is occurred, CPU read the interrupt information (the interrupt number
and interrupt request level) in the interrupt sequence.
The interrupt request bit of the certain interrupt written in address 0000016 will then be set to “0”.
Reading address 0000016 by software sets enabled highest priority interrupt source request bit to “0”.
Though the interrupt is generated, the interrupt routine may not be executed.
Do not read address 0000016 by software.
(2) Setting the stack pointer
The value of the stack pointer immediately after reset is initialized to 000016. Accepting an
interrupt before setting a value in the stack pointer may become a factor of runaway. Be sure to
set a value in the stack pointer before accepting an interrupt.
_______
When using the NMI interrupt, initialize the stack point at the beginning of a program. Concerning
_______
the first instruction immediately after reset, generating any interrupts including the NMI interrupt is
prohibited.
_______
(3) The NMI interrupt
_______
The NMI interrupt can not be disabled. Be sure to connect NMI pin to Vcc via a pull-up resistor if
unused.
_______
Do not get either into stop mode with the NMI pin set to “L”.
____________
(1) When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main clock
oscillation is stabilized.
(2) When switching to either wait mode or stop mode, instructions occupying four bytes either from the
WAIT instruction or from the instruction that sets the every-clock stop bit to “1” within the instruction
queue are prefetched and then the program stops. So put at least four NOPs in succession either to
the WAIT instruction or to the instruction that sets the every-clock stop bit to “1”.
相关PDF资料 |
PDF描述 |
|---|---|
| M306N5MCT-XXXGP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100 |
| M306V0ME-XXXFP | 16-BIT, MROM, MICROCONTROLLER, PQFP100 |
| M306V0EEFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP100 |
| M306V2ME-XXXFP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
| M306V2EEFP | 16-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M306N5MCT-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU |
| M306N5MCT-XXXGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU |
| M306N5MCV-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU |
| M306N5MCV-XXXGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU |
| M306N5MC-XXXGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Renesas MCU |
发布紧急采购，3分钟左右您将得到回复。