参数资料
型号: M306V2ME-XXXFP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100
封装: 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100
文件页数: 211/273页
文件大小: 2352K
代理商: M306V2ME-XXXFP
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页当前第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页第243页第244页第245页第246页第247页第248页第249页第250页第251页第252页第253页第254页第255页第256页第257页第258页第259页第260页第261页第262页第263页第264页第265页第266页第267页第268页第269页第270页第271页第272页第273页
Rev.1.40
Oct 06, 2004 page 40 of 269
M306V2ME-XXXFP, M306V2EEFP
Figures 2.5.5 and 2.5.6 shows the system clock control registers 0 and 1.
Figure 2.5.6 System clock control register 1
System clock control register 1 (Note 1)
Symbol
Address
When reset
CM1
000716
2016
Bit name
Function
Bit symbol
b7b6b5b4b3b2b1b0
CM10
All clock stop control bit
(Note 4)
0 : Clock on
1 : All clocks off (stop mode)
Notes 1: Set bit 0 of the protect register (address 000A16) to “1” before writing to this register.
2: This bit changes to “1” when shifting from high-speed/medium-speed mode to stop mode and at a
reset. When shifting from low-speed/low power dissipation mode to stop mode, the value before stop
mode is retained.
3: Can be selected when bit 6 of the system clock control register 0 (address 000616) is “0.”
If “1”, division mode is fixed at 8.
4: If this bit is set to “1,” XOUT turns “H,” and the built-in feedback resistor is cut off. XCIN and XCOUT turn
high-impedance state.
CM15
XIN-XOUT drive capacity
select bit (Note 2)
0 : LOW
1 : HIGH
W
R
CM16
CM17
Main clock division
select bit 1 (Note 3)
0 0 : No division mode
0 1 : Division by 2 mode
1 0 : Division by 4 mode
1 1 : Division by 16 mode
b7 b6
0
Reserved bits
Must always be set to
“0”
0
Figures 2.5.5 System clock control register 0
System clock control register 0 (Note 1)
Symbol
Address
When reset
CM0
000616
4816
Bit name
Function
Bit symbol
b7
b6
b5
b4
b3
b2
b1
b0
0 0 : I/O port P57
0 1 : fC output
1 0 : f8 output
1 1 : f32 output
b1 b0
CM07
CM05
CM04
CM03
CM01
CM02
CM00
CM06
Clock output function
select bit
(Valid only in single-chip
mode)
WAIT peripheral function
clock stop bit
0 : Do not stop peripheral function clock in wait mode
1 : Stop peripheral function clock in wait mode (Note 8)
XCIN-XCOUT drive capacity
select bit (Note 2)
0 : LOW
1 : HIGH
Port XC select bit
0 : I/O port
1 : XCIN-XCOUT generation
Main clock (XIN-XOUT)
stop bit (Notes 3, 4, 5)
0 : On
1 : Off
Main clock division select
bit 0 (Note 7)
0 : CM16 and CM17 valid
1 : Division by 8 mode
System clock select bit
(Note 6)
0 : XIN, XOUT
1 : XCIN, XCOUT
Notes 1: Set bit 0 of the protect register (address 000A16) to “1” before writing to this register.
2: Changes to “1” when shifting to stop mode and at a reset.
3: When entering power saving mode, main clock stops using this . When returning from stop mode and
operating with XIN, set this bit to “0.” When main clock oscillation is operating by itself, set system clock select
bit (CM07) to “1” before setting this bit to “1”.
4: When inputting external clock, only clock oscillation buffer is stopped and clock input is acceptable.
5: If this bit is set to “1,” XOUT turns “H.” The built-in feedback resistor remains being connected, so XIN turns
pulled up to XOUT (“H”) via the feedback resistor.
6: Set port Xc select bit (CM04) to “1” and stabilize the sub-clock oscillating before setting to this bit from “0” to
“1.” Do not write to both bits at the same time. And also, set the main clock stop bit (CM05) to “0” and stabilize
the main clock oscillating before setting this bit from “1” to “0.”
7: This bit changes to “1” when shifting from high-speed/medium-speed mode to stop mode and at a reset. When
shifting from low-speed/low power dissipation mode to stop mode, the value before stop mode is retained.
8: fC32 is not included.
W
R
相关PDF资料
PDF描述
M306V8FJFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116
M30L40C-E3/4W 15 A, 40 V, SILICON, RECTIFIER DIODE, TO-220AB
M31022AGLJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, LVDS OUTPUT
M31002AMPJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, PECL OUTPUT
M31022BGLNFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, LVDS OUTPUT
相关代理商/技术参数
参数描述
M306V5EESP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5EESS 功能描述:EPROM MCU/M16C(TV/VTR) RoHS:否 类别:编程器,开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230,RCB231,RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M306V5ME 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5ME-101SP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5ME-105SPZ 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER