- 您现在的位置：买卖IC网 > PDF目录80579 > M30843FJFP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M30843FJFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 69/91页 |
| 文件大小： | 903K |
| 代理商： | M30843FJFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页当前第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页
70
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e parametric
limits
are
subject
to
change.
(3) Standard serial I/O Mode
The standard serial I/O mode inputs and outputs the software
commands, addresses and data needed to operate (read, pro-
gram, erase, etc.) the internal flash memory. This I/O is clock
synchronized serial. This mode requires a purpose-specific pe-
ripheral unit.
The standard serial I/O mode is different from the parallel I/O
mode in that the CPU controls flash memory rewrite (uses the
CPU rewrite mode), rewrite data input and so forth. The standard
serial I/O mode is started by connecting “H” to the P41 (CE) pin
and “H” to the CNVSS pin (when VCC = 4.5 to 5.5 V, connect to
VCC, and when VCC = 3.0 to 4.5 V, apply 4.5 V to 5.5 V to Vpp
from an external source), and releasing the reset operation. (In the
ordinary microcomputer mode, set CNVss pin to “L” level.)
This control program is written in the Boot ROM area when the
product is shipped from Mitsubishi. Accordingly, make note of the
fact that the standard serial I/O mode cannot be used if the Boot
ROM area is rewritten in parallel I/O mode. Figure 69 shows the
pin connections for the standard serial I/O mode.
In standard serial I/O mode, serial data I/O uses the four UART2
pins SCLK2, RxD2, TxD2 and SRDY2 (BUSY). The SCLK2 pin is the
transfer clock input pin through which an external transfer clock is
input. The TxD2 pin is for CMOS output. The SRDY2 (BUSY) pin
outputs “L” level when ready for reception and “H” level when re-
ception starts.
Serial data I/O is transferred serially in 8-bit units.
In standard serial I/O mode, only the User ROM area shown in
Figure 61 can be rewritten. The Boot ROM area cannot.
In standard serial I/O mode, a 7-byte ID code is used. When there
is data in the flash memory, commands sent from the peripheral
unit (programmer) are not accepted unless the ID code matches.
Outline Performance (Standard Serial I/O
Mode)
In standard serial I/O mode, software commands, addresses and
data are input and output between the MCU and peripheral units
(serial programer, etc.) using 4-wire clock-synchronized serial I/O
(UART2).
In reception, software commands, addresses and program data
are synchronized with the rise of the transfer clock that is input to
the SCLK2 pin, and are then input to the MCU via the RxD2 pin. In
transmission, the read data and status are synchronized with the
fall of the transfer clock, and output from the TxD2 pin.
The TxD2 pin is for CMOS output. Transfer is in 8-bit units with
LSB first.
When busy, such as during transmission, reception, erasing or
program execution, the SRDY2 (BUSY) pin is “H” level. Accord-
ingly, always start the next transfer after the SRDY2 (BUSY) pin is
“L” level.
Also, data and status registers in a memory can be read after in-
putting software commands. Status, such as the operating state of
the flash memory or whether a program or erase operation ended
successfully or not, can be checked by reading the status register.
Here following explains software commands, status registers, etc.
相关PDF资料 |
PDF描述 |
|---|---|
| M30853FHTGP | 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100 |
| M34553M4H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M37542M2-XXXHP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| M38D29GFHP | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 |
| M30201M4-XXXFP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M30843FJFP#D3 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 512KB FLASH 5V 100PQFP - Trays |
| M30843FJFP#D5 | 功能描述:IC M32C MCU FLASH 512K 100-LQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M32C/80/84 标准包装:160 系列:S08 核心处理器:S08 芯体尺寸:8-位 速度:40MHz 连通性:I²C，LIN，SCI，SPI 外围设备:LCD，LVD，POR，PWM，WDT 输入/输出数:53 程序存储器容量:32KB（32K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1.9K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 12x12b 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:64-LQFP 包装:托盘 |
| M30843FJFP#U3 | 功能描述:IC M32C MCU FLASH 512K 100LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M32C/80/84 标准包装:160 系列:S08 核心处理器:S08 芯体尺寸:8-位 速度:40MHz 连通性:I²C，LIN，SCI，SPI 外围设备:LCD，LVD，POR，PWM，WDT 输入/输出数:53 程序存储器容量:32KB（32K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1.9K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 12x12b 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:64-LQFP 包装:托盘 |
| M30843FJFP#U5 | 功能描述:IC M32C MCU FLASH 512K 100QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M32C/80/84 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M30843FJGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。