参数资料
型号: M37221MAH-XXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
封装: 0.450 INCH, 0.80 MM INCH, PLASTIC, SSOP-42
文件页数: 42/112页
文件大小: 1207K
代理商: M37221MAH-XXXFP
35
Rev. 1.0
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
M37221M4H/M6H/M8H/MAH–XXXSP/FP
M37221EASP/FP
MITSUBISHI MICROCOMPUTERS
8.6.4 I2C Control Register
The I2C control register (address 00DA16) controls the data commu-
nication format.
(1) Bits 0 to 2: bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. An interrupt request signal occurs immediately after the
number of bits specified with these bits are transmitted.
When a START condition is received, these bits become “0002” and
the address data is always transmitted and received in 8 bits.
(2) Bit 3: I2C-BUS interface use enable bit (ESO)
This bit enables usage of the multimaster I2C BUS interface. When
this bit is set to “0,” interface is in the disabled status so the SDA and
the SCL become high-impedance. When the bit is set to “1,” use of
the interface is enabled.
When ESO = “0,” the following is performed.
PIN = “1,” BB = “0” and AL = “0” are set (they are bits of the I2C
status register at address 00D916 ).
Writing data to the I2C data shift register (address 00D716) is dis-
abled.
(3) Bit 4: data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses. When
this bit is set to “0,” the addressing format is selected, so that ad-
dress data is recognized. When a match is found between a slave
address and address data as a result of comparison or when a gen-
eral call (refer to “8.6.5 I2C Status Register,” bit 1) is received, trans-
mission processing can be performed. When this bit is set to “1,” the
free data format is selected, so that slave addresses are not recog-
nized.
(4) Bit 5: addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit is
set to “0,” the 7-bit addressing format is selected. In this case, only
the high-order 7 bits (slave address) of the I2C address register (ad-
dress 00D816) are compared with address data. When this bit is set
to “1,” the 10-bit addressing format is selected and all the bits of the
I2C address register are compared with the address data.
(5) Bits 6 and 7: connection control bits between
I2C-BUS interface and ports
(BSEL0, BSEL1)
These bits control the connection between SCL and ports or SDA
and ports (refer to Figure 8.6.5).
Fig. 8.6.5 Connection Port Control by BSEL0 and BSEL1
Note: Set the corresponding direction register to “1” to use the
port as multi-master I2C-BUS interface.
“0”
“1” BSEL0
SCL1/P11
SCL2/P12
“0”
“1” BSEL1
“0”
“1” BSEL0
SDA1/P13
SDA2/P14
“0”
“1” BSEL1
Multi-master
I2C-BUS
interface
SCL
SDA
相关PDF资料
PDF描述
M37221MAH-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
MC68EN360ZP25VL 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PBGA357
M38003M6-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
M37471E8-XXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP56
M30620MC-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
M37221MAH-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37224M3 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37224M3-050SP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37224M3-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225ECSP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER