参数资料
型号: M37224M3-XXXSP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
封装: 0.600 INCH, 1.778 MM PITCH, SHRINK, PLASTIC, DIP-42
文件页数: 49/83页
文件大小: 901K
代理商: M37224M3-XXXSP
M37224M3-XXXSP
MITSUBISHI MICROCOMPUTERS
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
53
OSC2
OSC1
L
C1
C2
RESET
Vss
Vcc
Circuit example 1
RESET
Vss
Vcc
Circuit example 2
Note :
DISPLAY OSCILLATION CIRCUIT
The CRT display clock oscillation circuit has a built-in clock oscilla-
tion circuits, so that a clock for CRT display can be obtained simply
by connecting an LC, an RC, a ceramic resonator or a quartz-crystal
oscillator circuit across the pins OSC 1 and OSC 2. Select the clock
for display with bits 0 and 1 of the CRT clock selection register (ad-
dress 00ED16).
ADDRESSING MODE
The memory access is reinforced with 17 kinds of addressing modes.
Refer to SERIES 740 <Software> User’s Manual for details.
MACHINE INSTRUCTIONS
There are 71 machine instructions. Refer to SERIES 740 <Soft- ware>
User’s Manual for details.
PROGRAMMING NOTES
(1) The divide ratio of the timer is 1/(n+1).
(2) Even though the BBC and BBS instructions are executed imme-
diately after the interrupt request bits are modified (by the pro-
gram), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
(3) After the ADC and SBC instructions are executed (in the decimal
mode), one instruction cycle (such as an NOP) is needed before
the SEC, CLC, or CLD instruction is executed.
(4) An NOP instruction is needed immediately after the execution of
a PLP instruction.
(5) In order to avoid noise and latch-up, connect a bypass capacitor
(
≈ 0.1 F) directly between the VCC pin–VSS pin and the VCC pin–
CNVSS pin, using a thick wire.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
(1) Mask ROM Order Confirmation From.
(2) Mask Specification From.
(3) Data to be written to ROM, in EPROM form (32-pin DIP Type
27C101, three identical copies).
AUTO-CLEAR CIRCUIT
When a power source is supplied, the auto-clear function will oper-
______
ate by connecting the following circuit to the RESET pin.
Fig. 59. Auto-clear Circuit Example
Fig. 58. Display Oscillation Circuit
Make the level change from “L” to “H” at the point at
which the power source voltage exceeds the specified
voltage.
相关PDF资料
PDF描述
M37270MF-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64
M37273MFH-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52
M3727GM8-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
M37280MFH-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
M37280MKH-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
相关代理商/技术参数
参数描述
M37225ECSP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225M6 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225M8 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37225MA 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M372429100 制造商:ITW Switches 功能描述:IN-RUSH