参数资料
型号: M37272M6H-XXXSP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
封装: 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42
文件页数: 99/132页
文件大小: 1736K
代理商: M37272M6H-XXXSP
68
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M37272M6H/M8H/MAH/MFH–XXXSP/FP
M37272E8SP/FP, M37272EFSP/FP
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
The horizontal display start position is common to all blocks, and can
be set in 128 steps (where 1 step is 4TOSC, TOSC being the OSD
oscillation cycle) as values “0016” to “FF16” in bits 0 to 6 of the hori-
zontal position register (address 00D116). The horizontal position reg-
ister is shown in Figure 8.11.8.
Fig. 8.11.8 Horizontal Position Register
Notes 1 : 1TC (TC : OSD clock cycle divided in pre-divide circuit) gap occurs
between the horizontal display start position set by the horizontal
position register and the most left dot of the 1st block. Accordingly,
when 2 blocks have different pre-divide ratios, their horizontal dis-
play start position will not match.
2 : The horizontal start position is based on the OSD clock source cycle
selected for each block. Accordingly, when 2 blocks have different
OSD clock source cycles, their horizontal display start position will
not match.
3 : When setting “0016” to the horizontal position register, it needs ap-
proximately 62TOSC (= Tdef) interval from a rising edge (when nega-
tive polarity is selected) of HSYNC signal to the horizontal display start
position.
Fig. 8.11.9 Notes on Horizontal Display Start Position
4TOSC’ N
4TOSC N
HSYNC
1TC
Note 1
Note 2
Block 2 (Pre-divide ratio = 2, clock source = data slicer clock)
Block 3 (Pre-divide ratio = 3, clock source = data slicer clock)
Block 4 (Pre-divide ratio = 3, clock source = OSC1)
Tdef
Tdef
N
: Value of horizontal position register (decimal notation)
1TC : OSD clock cycle divided in pre-divide circuit
TOSC : OSD oscillation cycle
Tdef
: 62 TOSC
b7 b6 b5 b4 b3 b2 b1 b0
Horizontal position register (HP) [Address 00D1 16]
B
Name
Horizontal Position Register
7
Horizontal display start
position control bits
(HP0 to HP6)
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
Functions
After reset R W
Horizontal display start positions
128 steps (0016 to 7F16)
(1 step is 4TOSC)
0
RW
R —
0
to
6
Note: The setting value synchronizes with the V SYNC.
相关PDF资料
PDF描述
M37540E8V-XXXGP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36
M37540M4T-XXXFP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
MC9S12DJ128EMFU 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
M30622M8A-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
MC9328MXLCVP15 150 MHz, RISC PROCESSOR, PBGA225
相关代理商/技术参数
参数描述
M37272M6-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272M6-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272M8 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272M8-062FP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37272M8-084FP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER