参数资料
型号: M3727GM8-XXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
封装: 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
文件页数: 56/129页
文件大小: 1211K
代理商: M3727GM8-XXXFP
32
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M3727GM6/M8–XXXSP/FP
M37272E8SP/FP
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
8.6.4 I2C Control Register
The I2C control register (address 00F916) controls the data commu-
nication format.
(1) Bits 0 to 2: bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. An interrupt request signal occurs immediately after the
number of bits specified with these bits are transmitted.
When a START condition is received, these bits become “0002” and
the address data is always transmitted and received in 8 bits.
(2) Bit 3: I2C interface use enable bit (ESO)
This bit enables usage of the multimaster I2C BUS interface. When
this bit is set to “0,” the use disable status is provided, so the SDA
and the SCL become high-impedance. When the bit is set to “1,” use
of the interface is enabled.
When ESO = “0,” the following is performed.
PIN = “1,” BB = “0” and AL = “0” are set (they are bits of the I2C
status register at address 00F816 ).
Writing data to the I2C data shift register (address 00F616) is dis-
abled.
(3) Bit 4: data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses. When
this bit is set to “0,” the addressing format is selected, so that ad-
dress data is recognized. When a match is found between a slave
address and address data as a result of comparison or when a gen-
eral call (refer to “8.6.5 I2C Status Register,” bit 1) is received, trans-
mission processing can be performed. When this bit is set to “1,” the
free data format is selected, so that slave addresses are not recog-
nized.
(4) Bit 5: addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit is
set to “0,” the 7-bit addressing format is selected. In this case, only
the high-order 7 bits (slave address) of the I2C address register (ad-
dress 00F716) are compared with address data. When this bit is set
to “1,” the 10-bit addressing format is selected, all the bits of the I2C
address register are compared with address data.
(5) Bits 6 and 7: connection control bits between
I2C-BUS interface and ports
(BSEL0, BSEL1)
These bits controls the connection between SCL and ports or SDA
and ports (refer to Figure 8.6.5).
Fig. 8.6.5 Connection Port Control by BSEL0 and BSEL1
Note: Set the corresponding direction register to “1” to use the
port as multi-master I2C-BUS interface.
“0”
“1” BSEL0
SCL/P11
SCL2/P12
“0”
“1” BSEL1
“0”
“1” BSEL0
SDA1/P13
SDA2/P14
“0”
“1” BSEL1
Multi-master
I2C-BUS
interface
SCL
SDA
相关PDF资料
PDF描述
M37542M2V-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO36
MC9S12DJ256CCPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
MC9S12DT256CCPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
MC912D60CMFU8 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
MC68MH360ZP25L 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PBGA357
相关代理商/技术参数
参数描述
M3727GM8-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37280EKSP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37280EKSS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
M37280MF 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37280MF_03 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER