- 您现在的位置：买卖IC网 > PDF目录45032 > M37477E8TXXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO32 PDF资料下载
参数资料
| 型号： | M37477E8TXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO32 |
| 封装： | PLASTIC, SOP-32 |
| 文件页数： | 35/48页 |
| 文件大小： | 720K |
| 代理商： | M37477E8TXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
39
MITSUBISHI MICROCOMPUTERS
7477/ 7478 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PROM READING AND WRITING
Reading
To read the PROM, set the CE and OE pins to “L” level. Input the
address of the data (A0 to A14) to be read and the data will be out-
put to the I/O pins (D0 to D7). The data I/O pins will be floating
when either the CE or OE pin is in the “H” state.
Writing
To write to the PROM, set the OE pin to “H” level. The CPU will en-
ter the program mode when VPP is applied to the VPP pin. The
address to be written to is selected with pins A0 to A14, and the
data to be written is input to pins D0 to D7. Set the CE pin to “L”
level to begin writing.
Note on Writing
When using a PROM programmer, the address range should be
between 400016 and 7FFF16. When data is written between ad-
dresses 000016 and 7FFF16, fill addresses 000016 to 3FFF16 with
FF16.
Erasing
Data can only erased on the M37478E8SS ceramic package,
which includes a window. To erase data on this chip, use an ultra-
violet light source with a 2537 Angstrom wave length. The
minimum radiation power necessary for erasing is 15W s/cm2.
NOTES ON HANDLING
(1) Sunlight and fluorescent light contain wave lengths capable of
erasing data. For ceramic package types, cover the transpar-
ent window with a seal (provided) when this chip is in use.
However, this seal must not contact the lead pins.
(2) Before erasing, the glass should be cleaned and stains such
as finger prints should be removed thoroughly. If these stains
are not removed, complete erasure of the data could be pre-
vented.
(3) Since a high voltage (12.5V) is used to write data, care should
be taken when turning on the PROM programmer’s power.
(4) For the programmable microcomputer (shipped in One Time
PROM version), Mitsubishi does not perform PROM write test
and screening in the assembly process and following pro-
cesses. To improve reliability after write, performing write and
test according to the flow below before use is recommended.
Writing with PROM programmer
Verify test with PROM programmer
Function check in target device
Screening (Caution) (Leave at 150
°C for 40 hours.)
Caution : Since the screening temperature is higher than storage
temperature, never expose to 150°C exceeding 100
hours.
Read-out
Output disable
Programming
Programming verify
Program disable
Output
Floating
Input
Output
Floating
VIL
VIH
VIL
VIH
VCC
VPP
VCC
VIL
VIH
Pin
Mode
__
CE
__
OE
VPP
VCC
Data I/O
Note : VIL and VIH indicate an “L” and an “H” input voltage, respectively.
Table 3. I/O signal in each mode
相关PDF资料 |
PDF描述 |
|---|---|
| M37477E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO32 |
| M37478E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP56 |
| M37478E8TXXXFP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP56 |
| M37478M4TXXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37477M4TXXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37477E8TXXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37477E8TXXXSP/FP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37477E8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37477E8-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37477E8-XXXSP/FP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。