- 您现在的位置：买卖IC网 > PDF目录80512 > M37540E8GP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 PDF资料下载
参数资料
| 型号： | M37540E8GP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件页数： | 21/90页 |
| 文件大小： | 830K |
| 代理商： | M37540E8GP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页
7540 Group
Rev.4.00
Jun 21, 2004
page 26 of 82
REJ03B0011-0400Z
qTimer Y
Timer Y is an 8-bit timer and counts the prescaler Y output.
When Timer Y underflows, the timer Y interrupt request bit is set to
“1”.
Prescaler Y is an 8-bit prescaler and counts the signal selected by
the timer Y count source selection bit.
Prescaler Y has the prescaler Y latch to retain the reload value.
Timer Y has the timer Y primary latch and timer Y secondary latch
to retain the reload value.
The value of prescaler Y latch is set to Prescaler Y when
Prescaler Y underflows.The value of timer Y primary latch or timer
Y secondary latch are set to Timer Y when Timer Y underflows.
As for the value to transfer to Timer Y, either of timer Y primary or
timer Y secondary is selected depending on the timer Y operating
mode.
When writing to Prescaler Y (PREY), timer Y primary (TYP) or
timer Y secondary (TYS) is executed, writing to “latch only” or
“latch and prescaler (timer)” can be selected by the setting value
of the timer Y write control bit. Be sure to set the timer Y write con-
trol bit because there are some notes according to the operating
mode.
When reading from Prescaler Y (PREY) is executed, the count
value of Prescaler Y is read out. When reading from timer Y pri-
mary (TYP) is executed, the count value of Timer Y is read out.
The count value of Timer Y can be read out by reading from the
timer Y primary (TYP) even when the value of timer Y primary
latch or timer Y secondary latch is counted. When reading the
timer Y secondary (TYS) is executed, the undefined value is read
out.
Timer Y can be selected in one of 2 operating modes by setting
the timer Y operating mode bits of the timer Y, Z mode register.
(1) Timer mode
Prescaler Y counts the count source selected by the timer Y count
source selection bits. Each time the count clock is input, the con-
tents of Prescaler Y is decremented by 1. When the contents of
Prescaler Y reach “0016”, an underflow occurs at the next count
clock, and the prescaler Y latch is reloaded into Prescaler Y. The
division ratio of Prescaler Y is 1/(n+1) provided that the value of
Prescaler Y is n.
The contents of Timer Y is decremented by 1 each time the under-
flow signal of Prescaler Y is input. When the contents of Timer Y
reach “0016”, an underflow occurs at the next count clock, and the
timer Y primary latch is reloaded into Timer Y and count continues.
(In the timer mode, the contents of timer Y primary latch is
counted. Timer Y secondary latch is not used in this mode.)
The division ratio of Timer Y is 1/(m+1) provided that the value of
Timer Y is m. Accordingly, the division ratio of Prescaler Y and
Timer Y is 1/((n+1)(m+1)) provided that the value of Prescaler Y
is n and the value of Timer Y is m.
In the timer mode, writing to “latch only” or “latches and Prescaler
Y and timer Y primary” can be selected by the setting value of the
timer Y write control bit.
(2) Programmable waveform generation mode
In the programmable waveform generation mode, timer counts the
setting value of timer Y primary and the setting value of timer Y
secondary alternately, the waveform inverted each time Timer Y
underflows is output from TYOUT pin.
When using this mode, be sure to set “1” to the timer Y write con-
trol bit to select “write to latch only”. Also, set the port P01 direction
registers to output mode.
The active edge of output waveform is set by the timer Y output
level latch (b5) of the timer Y, Z waveform output control register
(PUM). When “0” is set to b5 of PUM, “H” interval by the setting
value of TYP or “L” interval by the setting value of TYS is output
alternately. When “1” is set to b5 of PUM, “L” interval by the setting
value of TYP or “H” interval by the setting value of TYS is output
alternately.
Also, in this mode, the primary interval and the secondary interval
of the output waveform can be extended respectively for 0.5 cycle
of timer count source clock by setting the timer Y primary wave-
form extension control bit (b2) and the timer Y secondary
waveform extension control bit (b3) of PUM to “1”. As a result, the
waveforms of more accurate resolution can be output.
When b2 and b3 of PUM are used, the frequency and duty of the
output waveform are as follows;
Waveform frequency:
FYOUT=
Duty:
DYOUT=
TMYCL: Timer Y count source (frequency)
TYP: Timer Y primary (8bit)
TYS: Timer Y secondary (8bit)
EXPYP: Timer Y primary waveform extension control bit (1bit)
EXPYS: Timer Y secondary waveform extension control bit (1bit)
In the programmable waveform generation mode, when values of
the TYP, TYS, EXPYP and EXPYS are changed, the output wave-
form is changed at the beginning (timer Y primary waveform
interval) of waveform period.
When the count values are changed, set values to the TYS,
EXPYP and EXPYS first. After then, set the value to TYP. The val-
ues are set all at once at the beginning of the next waveform
period when the value is set to TYP. (When writing at timer stop is
executed, writing to TYP at last is required.)
Notes on programmable waveform generation mode is described
below;
2TMYCL
2(TYP+1)+2(TYS+1)+(EXPYP+EXPYS)
2(TYP+1)+EXPYP
(2(TYP+1)+EXPYP)+(2(TYS+1)+EXPYS)
相关PDF资料 |
PDF描述 |
|---|---|
| M38224M6MXXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38227MCA-XXXFP | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80 |
| MB96F348AWAXXXPMC-GSE2 | 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB90348CESPFV | MICROCONTROLLER, PQFP100 |
| MB90F346CESPFV | MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37540E8GP#U0 | 功能描述:IC 7540 MCU OTP 32K 32LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37540E8SP | 制造商:Renesas Electronics Corporation 功能描述: |
| M37540E8T-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8T-XXXGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540E8V-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。