- 您现在的位置：买卖IC网 > PDF目录80460 > M37544M2-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 PDF资料下载
参数资料
| 型号： | M37544M2-XXXSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| 封装： | 0.400 INCH, 1.78 MM PITCH, PLASTIC, SDIP-32 |
| 文件页数： | 39/70页 |
| 文件大小： | 645K |
| 代理商： | M37544M2-XXXSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
7544 Group
Rev.1.04
2004.06.08
page 42 of 66
REJ03B0012-0104Z
Fig. 54 Bypass capacitor across the VSS line and the VCC line
2. Connection of bypass capacitor across VSS line and VCC line
Connect an approximately 0.1
F bypass capacitor across the VSS
line and the VCC line as follows:
Connect a bypass capacitor across the VSS pin and the VCC pin
at equal length.
Connect a bypass capacitor across the VSS pin and the VCC pin
with the shortest possible wiring.
Use lines with a larger diameter than other signal lines for VSS
line and VCC line.
Connect the power source wiring via a bypass capacitor to the
VSS pin and the VCC pin.
3. Wiring to analog input pins
Connect an approximately 100
to 1 k resistor to an analog
signal line which is connected to an analog input pin in series.
Besides, connect the resistor to the microcomputer as close as
possible.
Connect an approximately 1000 pF capacitor across the Vss pin
and the analog input pin. Besides, connect the capacitor to the
Vss pin as close as possible. Also, connect the capacitor across
the analog input pin and the Vss pin at equal length.
<Reason>
Signals which is input in an analog input pin (such as an A/D con-
verter/comparator input pin) are usually output signals from
sensor. The sensor which detects a change of event is installed far
from the printed circuit board with a microcomputer, the wiring to
an analog input pin is longer necessarily. This long wiring func-
tions as an antenna which feeds noise into the microcomputer,
which causes noise to an analog input pin.
Fig. 55 Analog signal line and a resistor and a capacitor
The analog input pin is connected to the capacitor of a voltage
comparator. Accordingly, sufficient accuracy may not be ob-
tained by the charge/discharge current at the time of A/D
conversion when the analog signal source of high-impedance is
connected to an analog input pin. In order to obtain the A/D con-
version result stabilized more, please lower the impedance of an
analog signal source, or add the smoothing capacitor to an ana-
log input pin.
VSS
VCC
VSS
VCC
N.G.
O.K.
Analog
input pin
VSS
Noise
Thermistor
Microcomputer
N.G.
O.K.
(Note)
Note : The resistor is used for dividing
resistance with a thermistor.
(5) Wiring to VPP pin of One Time PROM version
Connect an approximately 5 k
resistor to the VPP pin the shortest
possible in series and also to the Vss pin. When not connecting
the resistor, make the length of wiring between the VPP pin and
the Vss pin the shortest possible.
Note: Even when a circuit which included an approximately 5 k
resistor is used in the Mask ROM version, the microcom-
puter operates correctly.
<Reason>
The VPP pin of the One Time PROM is the power source input pin
for the built-in PROM. When programming in the built-in PROM,
the impedance of the VPP pin is low to allow the electric current for
writing flow into the PROM. Because of this, noise can enter eas-
ily. If noise enters the VPP pin, abnormal instruction codes or data
are read from the built-in PROM, which may cause a program run-
away.
Fig. 53 Wiring for the VPP pin of the One Time PROM
CNVSS/VPP
VSS
shortest
distance
About 5k
相关PDF资料 |
PDF描述 |
|---|---|
| MB90567PMC | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| M37221MAH-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M38037M8-XXXHP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFFP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFHSP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37544RSS | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37545G1KP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37545G2KP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37545G4GP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37545G4GP#U0 | 功能描述:MCU 2/5V 16K 32-LQFP QZ-ROM RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。