- 您现在的位置：买卖IC网 > PDF目录80549 > M37547G2FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 PDF资料下载
参数资料
| 型号： | M37547G2FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| 封装： | 8.40 X 15 MM, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件页数： | 43/97页 |
| 文件大小： | 1064K |
| 代理商： | M37547G2FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
REJ03B0156-0122
Rev.1.22
Mar 31, 2009
page 48 of 94
7547 Group
[Transmit buffer register 2/receive buffer register 2 (TB2/
RB2)] 002E16
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Serial I/O2 status register (SIO2STS)] 002F16
The read-only serial I/O2 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O2
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O2 enable bit SIOE
(bit 7 of the serial I/O2 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O2 status register are initialized to “0” at
reset, but if the transmit enable bit of the serial I/O2 control regis-
ter has been set to “1”, the transmit shift completion flag (bit 2)
and the transmit buffer empty flag (bit 0) become “1”.
[Serial I/O2 control register (SIO2CON)] 003016
The serial I/O2 control register consists of eight control bits for the
serial I/O2 function.
[UART2 control register (UART2CON)] 003116
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer.
[Baud rate generator 2 (BRG2)] 003216
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
■ Notes on Serial I/O2
Serial I/O interrupt
When setting the transmit enable bit to “1”, the serial I/O transmit
interrupt request bit is automatically set to “1”. When not requiring
the interrupt occurrence synchronized with the transmission en-
abled, take the following sequence.
Set the serial I/O transmit interrupt enable bit to “0” (disabled).
Set the transmit enable bit to “1”.
Set the serial I/O transmit interrupt request bit to “0” after 1 or
more instructions have been executed.
Set the serial I/O transmit interrupt enable bit to “1” (enabled).
I/O pin function when serial I/O2 is enabled.
The functions of P06 and P07 are switched with the setting values
of a serial I/O2 mode selection bit and a serial I/O2 synchronous
clock selection bit as follows.
(1) Serial I/O2 mode selection bit → “1” :
Clock synchronous type serial I/O is selected.
Setup of a serial I/O2 synchronous clock selection bit
“0” : P06 pin turns into an output pin of a synchronous clock.
“1” : P06 pin turns into an input pin of a synchronous clock.
Setup of a SRDY2 output enable bit (SRDY)
“0” : P07 pin can be used as a normal I/O pin.
“1” : P07 pin turns into a SRDY2 output pin.
(2) Serial I/O2 mode selection bit → “0” :
Clock asynchronous (UART) type serial I/O is selected.
Setup of a serial I/O2 synchronous clock selection bit
“0”: P06 pin can be used as a normal I/O pin.
“1”: P06 pin turns into an input pin of an external clock.
When clock asynchronous (UART) type serial I/O is selected, it is
P07 pin. It can be used as a normal I/O pin.
相关PDF资料 |
PDF描述 |
|---|---|
| M38D58G8-XXXHP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80 |
| MC6805R3S | 8-BIT, MROM, MICROCONTROLLER, CDIP40 |
| MC68HC705P6MDW | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC908QB4CDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
| MC908QL2CDTE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37547G2FP#U0 | 功能描述:MCU 2/5V 8KB 36-SSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| M37547G2-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37547G4FP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37547G4FP#U0 | 功能描述:MCU 2/5V 16K 36-SSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| M37547G4-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。