参数资料
型号: M37630E4FS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, UVPROM, 10 MHz, MICROCONTROLLER, CQCC80
封装: 0.80 MM PITCH, CERAMIC, LCC-80
文件页数: 11/48页
文件大小: 563K
代理商: M37630E4FS
MITSUBISHI MICROCOMPUTERS
7630 Group
19
MITSUBISHI
ELECTRIC
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMERS
The 7630 group has five timers: two 16-bit timers and three 8-bit
timers . All these timers will be described in detail below.
16-bit Timers
Timers X and Y are 16-bit timers with multiple operating modes.
Please refer to Fig. 17.
Fig. 17
Block diagram of timers X and Y (
φ is internal system clock)
Timer X
Timer X is a 16-bit timer with a 16-bit reload latch supporting the fol-
lowing operating modes:
(1) Timer mode
(2) Bi-phase counter mode
(3) Event counter mode
(4) Pulse width measurement mode
These modes can be selected by the timer X mode register (TXM).
In the timer- and pulse width measurement mode, the timer’s count
source can be selected by the timer X count source selection bits of
the timer Y mode register (TYM). Please refer to the Figures below
for the TXM and TYM bit assignment.
On read or write access to timer X, note that the high-order and low-
order bytes must be accessed in the specific order.
Write method
When writing to the timer X, write the low-order byte first. The data
written is stored in a temporary register which is assigned to the
same address as TXL. Next, write the high-order byte. When this is
finished, the data is placed in the timer X high-order reload latch
and the low-order byte is transferred from its temporary register to
the timer X low-order reload latch. Depending on the timer X write
control bit, the latch contents are reloaded to the timer immediately
(write control bit = “0”) or on the next timer underflow (write control
bit = “1”).
Read method
When reading the timer X, read the high-order byte first. This
causes the timer X high- and low-order bytes to be transferred to
temporary registers being assigned to the same addresses as TXH
and TXL. Next, read the low-order byte which is read from the tem-
porary register. This method assures the correct timer value can be
read during the timer count operation.
Timer X count stop control
Regardless of the actual operating mode, timer X can be stopped
by setting the timer X count stop bit (bit 7 of the timer X mode regis-
ter) to “1”.
TYM5, 4=“11”
TYM7
1/16
1/64
1/128
TYM1,0
φ
P13/TX0
P14/CNTR0
edge detector
sign generator
TXL counter (8)
TXH latch (8)
TXH counter (8)
TXM7
TXL latch (8)
count
direction
control
TXM5, 4
down
“00”, “10”,
“11”
“01”
“00”, “11”
“01”
“10”
TXM6
TXM5, 4=“11”
TX interrupt request
CNTR0 interrupt request
1/8
1/32
1/64
P15/CNTR1
TYM6
TYM5, 4
“10”
“0x”, “11”
TYL counter (8)
TYH latch (8)
TYH counter (8)
TYL latch (8)
TY interrupt request
CNTR1 interrupt request
rising edge detector
falling edge detector
TYM5, 4=“01”
TYM5, 4
“11”
“0x”, “10”
“0”
“1”
TYM3, 2
1/4
1/2
TXM5,4
“00”
“01”
“10”
“11”
“00”
“01”
“10”
“11”
“0”
“1”
相关PDF资料
PDF描述
M37630E4T-XXXFP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44
M37630E4FP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44
M37640E8FP 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
M37640E8FS 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
M37640M8-XXXFP 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M37630E4T-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630E4T-XXXFS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630M4T 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:Baseband Processor for ‘Leisure’ Radios with Data
M37630M4T-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630M4T-XXXFS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER