参数资料
型号: M37630E4FS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, UVPROM, 10 MHz, MICROCONTROLLER, CQCC80
封装: 0.80 MM PITCH, CERAMIC, LCC-80
文件页数: 20/48页
文件大小: 563K
代理商: M37630E4FS
MITSUBISHI MICROCOMPUTERS
7630 Group
27
MITSUBISHI
ELECTRIC
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Baud rate selection
The baud rate of transmission and reception is determined by the
setting of the prescaler and the contents of the UART baud rate
generator register. It is calculated by: where
p is the division ratio of
the prescaler and
n is the content of UART baud rate generator reg-
ister. The prescalers division ration can be selected by the UART
mode register (see below).
UART mode register (UMOD, Structure of UART
mode register)
The UART mode register allows to select the transmission and
reception format with the following options:
word length: 7, 8 or 9 bits
parity: none, odd or even
stop bits: 1 or 2
It allows to select the prescalers division ratio as well.
UART baud rate generator (UBRG)
This 8 bit register allows to select the baud rate of the UART (see
above). Set this register to the desired value before enabling recep-
tion or transmission.
UART control register (UCON, Structure of UART
control register)
The UART control register consists of four control bits (bit 0 to bit 3)
which allow to control reception and transmission.
UART status register (USTS, Structure of UART
status register)
The read-only UART status register consists of 7 bits (bit 0 to bit 6)
which indicate the operating status of the UART function and vari-
ous errors.
(3) Handshaking signals
When used as transmitter the UART will recognize the clear-to-
send signal via P27/UCTS terminal for handshaking. When used as
receiver it will issue a request-to-send signal through P26/URTS
pin.
Clear-to-send input
When used as a transmitter (transmit enable bit set to “1”), the
UART starts transmission after recognizing “L” level on P27/UCTS.
After started the UART will continue to transmit regardless of the
actual level of P27/UCTS or status of the transmit enable bit.
Request-to-send output
The UART controls the P26/URTS output according to the following
conditions.
Table 5: Output control conditions
Fig. 26
Block diagram of UART
b
φ
16 pn
1
+
()
-----------------------------------
=
Condition
P26/URTS
Receive enable bit is set to “1”
“L”
Reception completed during receive enable
bit set to “1”
Start bit (falling edge) detected
“H”
Receive enable bit is set to “0” before recep-
tion started
Hardware reset
Receive initialization bit is set to “1”
UMOD4,3,2
φ
1
1/8
1/32
1/256
UMOD2, 1
UBRG (8)
transmit shift register (9)
transmission
control circuit
reception control
circuit
P25/UTXD
P27/UCTS
P26/URTS
bit counter
UMOD7, 6
UART status register
transmit buffer empty flag
receive error flags
receive buffer full interrupt request
receive error interrupt request
P24/URXD
transmit buffer (9)
data bus
transmit buffer empty interrupt request
transmit register empty interrupt request
receive buffer full flag
transmit register empty flag
receive shift register (9)
receive buffer (9)
UART control register
“00”
“01”
“10”
“11”
相关PDF资料
PDF描述
M37630E4T-XXXFP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44
M37630E4FP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44
M37640E8FP 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
M37640E8FS 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
M37640M8-XXXFP 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M37630E4T-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630E4T-XXXFS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630M4T 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:Baseband Processor for ‘Leisure’ Radios with Data
M37630M4T-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630M4T-XXXFS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER