- 您现在的位置：买卖IC网 > PDF目录67763 > M37905F8CFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | M37905F8CFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64 |
| 文件页数： | 17/37页 |
| 文件大小： | 392K |
| 代理商： | M37905F8CFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
16-BIT CMOS MICROCOMPUTER
M37905F8CFP, M37905F8CSP
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
21
Fig. 9 Programming flowchart
Fig. 10 Block erase flowchart
Start
Write 4016
Write,
Address, Data
Flash memory control
register Read
Full status check
Programming
Completed
NO
YES
RY/BY Status
Bit = 1?
Write 2016
Write D016,
Flash memory control
register Read
Full status check
Block erase Completed
NO
YES
Block address
Start
RY/BY Status
Bit = 1?
Erase All Block Command (2016/2016)
Writing command code “2016” at the 1st bus cycle and writing com-
mand code “2016” at the subsequent 2nd bus cycle initiate the con-
tinuous block erase (chip erase) operations for all the blocks.
The completion of the chip erase operation, as well as of the block
erase operation, is confirmed by a read of the flash memory control
register. The result of the automatic erase operation is also reported
by a read of the status register.
During the automatic erase operation (when the RY/BY status bit =
“0”), writing of commands and access to the flash memory must not
be performed.
Status Register
The status register is used to indicate whether the programming/
erase operation has been completed normally or terminated by an
error. By writing the read status register command (7016), the con-
tents of the status register can be read out; by writing the clear sta-
tus register command (5016), the contents of the status register can
be cleared.
Table 3 lists the definition of each bit of the status register.
The status register outputs “8016” after reset is removed.
The status of each bit is described below.
相关PDF资料 |
PDF描述 |
|---|---|
| M37905F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP64 |
| M37920F8CHP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M37920F8CGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38039MFL-XXXHP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38039MFL-XXXSP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37905F8CSP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905M4C | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXSP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M6C-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。