- 您现在的位置：买卖IC网 > PDF目录67763 > M37905F8CFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | M37905F8CFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64 |
| 文件页数： | 9/37页 |
| 文件大小： | 392K |
| 代理商： | M37905F8CFP |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
M37905F8CFP, M37905F8CSP
16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
14
Flash Memory Serial I/O Mode
In the flash memory serial I/O mode, addresses, data, and software
commands, which are required to read/program/erase the internal
flash memory, are serially input and output with a fewer pins and the
dedicated serial programmer.
In this mode, being different from the flash memory parallel I/O
mode, the CPU controls reprogramming of the flash memory (using
the CPU reprogramming mode), serial input of the reprogramming
data, etc.
The reprogramming control firmware for the flash memory serial I/O
mode has been stored in the boot ROM area on shipment of the
product from us. Note that, then, the flash memory serial I/O mode
will become unavailable if the boot ROM area has been repro-
grammed in the flash memory parallel I/O mode.
Note that, also, this reprogramming control firmware for the flash
memory serial I/O mode is subject to change.
Figures 5 and 6 show the pin connections in the flash memory serial
I/O mode.
The three pins, SCLK, SDA, and BUSY, are used to input and output
serial data.
The SCLK pin is the input pin of external transfer clocks. The SDA
pin is the I/O pin of transmit and receive data, and its output acts as
the N-channel open-drain output. To the SDA pin, connect an exter-
nal pullup resistor (about 1 k
). The BUSY pin is the output pin of the
BUSY flag (CMOS output) and goes “H” during BUSY periods owing
to a certain operation, such as transmit, receive, erase, program-
ming, etc.
Transmit and receive data are serially transferred 8 bits at a time.
In the flash memory serial I/O mode, only the user ROM area can be
reprogrammed; the boot ROM area is not accessible.
Addresses FF9016 to FF9F16 are the reserved area for the serial
programmer. Therefore, when the user uses the flash memory serial
I/O mode, do not program to this area.
相关PDF资料 |
PDF描述 |
|---|---|
| M37905F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP64 |
| M37920F8CHP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M37920F8CGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38039MFL-XXXHP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38039MFL-XXXSP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37905F8CSP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905M4C | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXSP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M6C-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。