- 您现在的位置：买卖IC网 > PDF目录45043 > M38207M8-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M38207M8-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 17/67页 |
| 文件大小： | 1099K |
| 代理商： | M38207M8-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
23
MITSUBISHI MICROCOMPUTERS
3820 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
Timer mode
The timer counts f(XIN)/16 (or f(XCIN)/16 in low-speed mode).
Period measurement mode
CNTR1 interrupt request is generated at rising/falling edge of
CNTR1 pin input signal. Simultaneously, the value in timer Y latch
is reloaded in timer Y and timer Y continues counting down. /Ex-
cept for the above-mentioned, the operation in period measure-
ment mode is the same as in timer mode.
The timer value just before the reloading at rising/falling of CNTR1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR1 pin input signal is found by
CNTR1 interrupt. When using a timer in this mode, set the corre-
sponding port P55 direction register to input mode.
Event counter mode
The timer counts signals input through the CNTR1 pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the corre-
sponding port P55 direction register to input mode.
Pulse width HL continuously measurement mode
CNTR1 interrupt request is generated at both rising and falling
edges of CNTR1 pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode. When using a timer in this mode, set
the corresponding port P55 direction register to input mode.
Note on CNTR1 Interrupt Active Edge Selec-
tion
CNTR1 interrupt active edge depends on the CNTR1 active edge
switch bit. However, in pulse width HL continuously measurement
mode, CNTR1 interrupt request is generated at both rising and
falling edges of CNTR1 pin input signal regardless of the setting of
CNTR1 active edge switch bit.
Fig. 13 Structure of timer Y mode register
Timer Y mode register
(TYM : address 002816)
Not used (return "0" when read)
Timer Y operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Period measurement mode
1 0 : Event counter mode
1 1 : Pulse width HL continuously
measurement mode
CNTR1 active edge switch bit
CNTR1 interrupt
0 : Falling edge active
1 : Rising edge active
Period measurement mode
0 : Measure falling edge to falling edge
1 : Measure rising edge to rising edge
Event counter mode
0 : Rising edge active
1 : Falling edge active
Timer Y stop control bit
0 : Count start
1 : Count stop
70
相关PDF资料 |
PDF描述 |
|---|---|
| M38207M8-XXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38222M4DXXXGP | 8-BIT, MROM, MICROCONTROLLER, PQFP80 |
| M38223E4-XXXHP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38222M2DXXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| M38223E4-XXXGP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38207RFS | 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk |
| M3821 BK001 | 制造商:Alpha Wire 功能描述:CBL 25COND 18AWG BLK 1000' |
| M3821 BK002 | 制造商:Alpha Wire 功能描述:CBL 25COND 18AWG BLK 500' |
| M3821 BK005 | 制造商:Alpha Wire 功能描述:CBL 25COND 18AWG BLK 100' |
| M38220E1DFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。