参数资料
型号: M38C29FFAHP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64
封装: 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件页数: 2/104页
文件大小: 1327K
代理商: M38C29FFAHP
Rev.2.00
May 28, 2004
page 8 of 100
38C2 Group (A Version)
FUNCTIONAL DESCRIPTION
Central Processing Unit (CPU)
The 38C2 group uses the standard 740 Family instruction set. Refer
to the table of 740 Family addressing modes and machine instruc-
tions or the 740 Family Software Manual for details on the instruction
set.
Machine-resident 740 Family instructions are as follows:
The FST and SLW instructions cannot be used.
The STP, WIT, MUL, and DIV instructions can be used.
The central processing unit (CPU) has six registers. Figure 5 shows
the 740 Family CPU register structure.
[Accumulator (A)]
The accumulator is an 8-bit register. Data operations such as arith-
metic data transfer, etc., are executed mainly through the accumula-
tor.
[Index Register X (X)]
The index register X is an 8-bit register. In the index addressing modes,
the value of the OPERAND is added to the contents of register X and
specifies the real address.
[Index Register Y (Y)]
The index register Y is an 8-bit register. In partial instruction, the
value of the OPERAND is added to the contents of register Y and
specifies the real address.
[Stack Pointer (S)]
The stack pointer is an 8-bit register used during subroutine calls
and interrupts. This register indicates start address of stored area
(stack) for storing registers during subroutine calls and interrupts.
The low-order 8 bits of the stack address are determined by the con-
tents of the stack pointer. The high-order 8 bits of the stack address
are determined by the stack page selection bit. If the stack page
selection bit is “0” , the high-order 8 bits becomes “0016”. If the stack
page selection bit is “1”, the high-order 8 bits becomes “0116”.
The operations of pushing register contents onto the stack and pop-
ping them from the stack are shown in Figure 6.
Store registers other than those described in Figure 6 with program
when the user needs them during interrupts or subroutine calls.
[Program Counter (PC)]
The program counter is a 16-bit counter consisting of two 8-bit regis-
ters PCH and PCL. It is used to indicate the address of the next in-
struction to be executed.
Fig. 5 740 Family CPU register structure
A
Accumulator
b7
b0
b7
b15
b0
b7
b0
X
Index register X
Y
Index register Y
S
Stack pointer
PCL
Program counter
PCH
N V T B D I Z C
Processor status register (PS)
Carry flag
Zero flag
Interrupt disable flag
Decimal mode flag
Break flag
Index X mode flag
Overflow flag
Negative flag
相关PDF资料
PDF描述
M38C29FFAFP 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64
M38K29F8LHP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
M38K27M4L-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
M38K29RFS 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, CPGA100
M41ST85YMH6 1 TIMER(S), REAL TIME CLOCK, PDSO28
相关代理商/技术参数
参数描述
M38C29FFAHP#U0 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 60KB FLASH 5V 64LQFP - Trays
M38C29FFFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29FFHP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER