- 您现在的位置：买卖IC网 > PDF目录80445 > M41T81SMY6T (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO18 PDF资料下载
参数资料
| 型号： | M41T81SMY6T |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO18 |
| 封装： | 0.300 INCH, LEAD FREE, PLASTIC, SOIC-18 |
| 文件页数： | 2/32页 |
| 文件大小： | 524K |
| 代理商： | M41T81SMY6T |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Operation
M41T81S
Doc ID 10773 Rev 6
Accordingly, the following bus conditions have been defined:
Bus not busy
Both data and clock lines remain high.
Start data transfer
A change in the state of the data line, from high to low, while the clock is high, defines the
START condition.
Stop data transfer
A change in the state of the data line, from low to high, while the clock is high, defines the
STOP condition.
Data valid
The state of the data line represents valid data when after a start condition, the data line is
stable for the duration of the high period of the clock signal. The data on the line may be
changed during the low period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a start condition and terminated with a stop condition.
The number of data bytes transferred between the start and stop conditions is not limited.
The information is transmitted byte-wide and each receiver acknowledges with a ninth bit.
By definition a device that gives out a message is called “transmitter,” the receiving device
that gets the message is called “receiver.” The device that controls the message is called
“master.” The devices that are controlled by the master are called “slaves.”
Acknowledge
Each byte of eight bits is followed by one acknowledge bit. This acknowledge bit is a low
level put on the bus by the receiver whereas the master generates an extra acknowledge
related clock pulse. A slave receiver which is addressed is obliged to generate an
acknowledge after the reception of each byte that has been clocked out of the slave
transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock
pulse in such a way that the SDA line is a stable low during the high period of the
acknowledge related clock pulse. Of course, setup and hold times must be taken into
account. A master receiver must signal an end of data to the slave transmitter by not
generating an acknowledge on the last byte that has been clocked out of the slave. In this
case the transmitter must leave the data line high to enable the master to generate the
STOP condition.
相关PDF资料 |
PDF描述 |
|---|---|
| M306N5MCT-XXXGP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100 |
| MC908GZ16VFA | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48 |
| MC908QY4MDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
| MC9S08SH4MTJ | MICROCONTROLLER, PDSO20 |
| MC9S12P32J0VQKR | MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M41T82 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover |
| M41T82_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover |
| M41T82_10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover |
| M41T82RM6E | 功能描述:实时时钟 Serial I2C bus RTC W/ battry switchover RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M41T82RM6F | 功能描述:实时时钟 Serial I2C bus RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。