参数资料
型号: M41T81SMY6T
厂商: STMICROELECTRONICS
元件分类: 时钟/数据恢复及定时提取
英文描述: 1 TIMER(S), REAL TIME CLOCK, PDSO18
封装: 0.300 INCH, LEAD FREE, PLASTIC, SOIC-18
文件页数: 6/32页
文件大小: 524K
代理商: M41T81SMY6T
Clock operation
M41T81S
Doc ID 10773 Rev 6
3
Clock operation
The 20-byte register map (see Table 2: Clock register map on page 15) is used to both set
the clock and to read the date and time from the clock, in a binary coded decimal format.
Tenths/hundredths of seconds, seconds, minutes, and hours are contained within the first
four registers.
Note:
Tenths/hundredths of seconds cannot be written to any value other than “00.”
Bits D6 and D7 of clock register 03h (century/hours register) contain the CENTURY
ENABLE bit (CEB) and the CENTURY bit (CB). Setting CEB to a '1' will cause CB to toggle,
either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial
state). If CEB is set to a '0,' CB will not toggle. Bits D0 through D2 of register 04h contain the
day (day of week). Registers 05h, 06h, and 07h contain the date (day of month), month and
years. The ninth clock register is the calibration register (this is described in the clock
calibration section). Bit D7 of register 01h contains the STOP bit (ST). Setting this bit to a '1'
will cause the oscillator to stop. If the device is expected to spend a significant amount of
time on the shelf, the oscillator may be stopped to reduce current drain. When reset to a '0'
the oscillator restarts within one second.
The eight clock registers may be read one byte at a time, or in a sequential block. Provision
has been made to assure that a clock update does not occur while any of the eight clock
addresses are being read. If a clock address is being read, an update of the clock registers
will be halted. This will prevent a transition of data during the READ.
Power-down timestamp
When a power failure occurs, the HALT (HT) bit will automatically be set to a '1.' This will
prevent the clock from updating the registers, and will allow the user to read the exact time
of the power-down event. Resetting the HT bit to a '0' will allow the clock to update the
registers with the current time.
Clock registers
The M41T81S offers 20 internal registers which contain clock, alarm, watchdog, flags,
square wave and calibration data. These registers are memory locations which contain
external (user accessible) and internal copies of the data (usually referred to as BiPORT
cells). The external copies are independent of internal functions except that they are
updated periodically by the simultaneous transfer of the incremented internal copy. The
internal divider (or clock) chain will be reset upon the completion of a WRITE to any clock
address.
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (00h to 07h). The update will resume either due to a stop condition or when
the pointer increments to any non-clock address (08h-13h).
Clock and alarm registers store data in BCD. Calibration, watchdog and square wave
registers store data in binary format.
相关PDF资料
PDF描述
M306N5MCT-XXXGP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
MC908GZ16VFA 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908QY4MDT 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MC9S08SH4MTJ MICROCONTROLLER, PDSO20
MC9S12P32J0VQKR MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M41T82 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover
M41T82_08 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover
M41T82_10 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial I2C bus RTC with battery switchover
M41T82RM6E 功能描述:实时时钟 Serial I2C bus RTC W/ battry switchover RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
M41T82RM6F 功能描述:实时时钟 Serial I2C bus RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube