- 您现在的位置：买卖IC网 > PDF目录45051 > M48T212Y-70MH6TR (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO44 PDF资料下载
参数资料
| 型号： | M48T212Y-70MH6TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
| 封装： | 0.330 INCH, PLASTIC, SOH-44 |
| 文件页数： | 13/32页 |
| 文件大小： | 473K |
| 代理商： | M48T212Y-70MH6TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
M48T212Y, M48T212V
20/32
Battery Low Warning
The M48T212Y/V automatically performs battery
voltage monitoring upon power-up and at factory-
programmed time intervals of approximately 24
hours. The Battery Low (BL) Bit, Bit D4 of Flags
Register 0h, will be asserted if the battery voltage
is found to be less than approximately 2.5V. The
BL Bit will remain asserted until completion of bat-
tery replacement and subsequent battery low
monitoring tests, either during the next power-up
sequence or the next scheduled 24-hour interval.
If a battery low is generated during a power-up se-
quence, this indicates that the battery is below ap-
proximately 2.5 volts and may not be able to
maintain data integrity in the SRAM. Data should
be considered suspect and verified as correct. A
fresh battery should be installed.
If a battery low indication is generated during the
24-hour interval check, this indicates that the bat-
tery is near end of life. However, data is not com-
promised due to the fact that a nominal VCC is
supplied. In order to insure data integrity during
subsequent periods of battery back-up mode, the
battery should be replaced. The SNAPHAT bat-
tery/crystal top should be replaced with VCC pow-
ering the device to avoid data loss.
Note: this will cause the clock to lose time during
the time interval the battery crystal is removed.
The M48T212Y/V only monitors the battery when
a nominal VCC is applied to the device. Thus appli-
cations which require extensive durations in the
battery back-up mode should be powered-up peri-
odically (at least once every few months) in order
for this technique to be beneficial.
Additionally, if a battery low is indicated, data in-
tegrity should be verified upon power-up via a
checksum or other technique.
Initial Power-on Defaults
Upon application of power to the device, the fol-
lowing register bits are set to a ’0' state: WDS,
BMB0-BMB4, RB0-RB1, AFE, ABE, W, and FT
(see Tabel 10).
Table 10. Default Values
Note: 1. WDS, BMB0-BMB4, RB0, RB1.
2. State of other control bits undefined.
3. State of other control bits remains unchanged.
4. Assuming these bits set to '1' prior to power-down.
Condition
W
R
FT
AFE
ABE
WATCHDOG
Register(1)
Initial Power-up
(Battery Attach for SNAPHAT)(2)
00000
0
RESET (3)
00000
0
Power-down (4)
01011
0
Subsequent Power-up
01000
0
相关PDF资料 |
PDF描述 |
|---|---|
| M48T248V-70PM1 | 0 TIMER(S), REAL TIME CLOCK, PDIP32 |
| M48T248Y-85PM1 | 0 TIMER(S), REAL TIME CLOCK, PDIP32 |
| M48T248Y-85PM1TR | 0 TIMER(S), REAL TIME CLOCK, PDIP32 |
| M48T35-70PC6 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| M48T35AV-10MH1F | 0 TIMER(S), REAL TIME CLOCK, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M48T212Y-85MH1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V/3.3V TIMEKEEPER[ CONTROLLER |
| M48T212Y-85MH1E | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V/3.3V TIMEKEEPER CONTROLLER Supervisor |
| M48T212Y-85MH1F | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V/3.3V TIMEKEEPER CONTROLLER Supervisor |
| M48T212Y-85MH1TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V/3.3V TIMEKEEPER[ CONTROLLER |
| M48T212Y-85MH6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V/3.3V TIMEKEEPER[ CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。