- 您现在的位置：买卖IC网 > PDF目录80586 > M48T37V-10MH1TR (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO44 PDF资料下载
参数资料
| 型号： | M48T37V-10MH1TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
| 封装： | 0.330 INCH, ROHS COMPLIANT, PLASTIC, SOH-44 |
| 文件页数： | 6/30页 |
| 文件大小： | 515K |
| 代理商： | M48T37V-10MH1TR |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Clock operations
M48T37Y, M48T37V
Doc ID 7019 Rev 9
3.4
Setting the alarm clock
Registers 7FF5h-7FF2h contain the alarm settings. The alarm can be configured to go off at
a predetermined time on a specific day of the month or repeat every day, hour, minute, or
second. It can also be programmed to go off while the M48T37Y/V is in the battery backup
mode of operation to serve as a system wake-up call.
RPT1-RPT4 put the alarm in the repeat mode of operation. Table 6 shows the possible
configurations. Codes not listed in the table default to the once per second mode to quickly
alert the user of an incorrect alarm setting.
Note:
User must transition address (or toggle chip enable) to see flag bit change.
When the clock information matches the alarm clock settings based on the match criteria
defined by RPT1-RPT4, AF is set. If AFE is also set, the alarm condition activates the
IRQ/FT pin. To disable alarm, write '0' to the alarm date registers and RPT1-4. The alarm
flag and the IRQ/FT output are cleared by a READ to the flags register as shown in Figure 7.
A subsequent READ of the flags register is necessary to see that the value of the alarm flag
has been reset to '0.'
The IRQ/FT pin can also be activated in the battery backup mode. The IRQ/FT will go low if
an alarm occurs and both the alarm in battery backup mode enable (ABE) and the AFE are
set. The ABE and AFE bits are reset during power-up, therefore an alarm generated during
power-up will only set AF. The user can read the flag register at system boot-up to
determine if an alarm was generated while the M48T37Y/V was in the deselect mode during
power-up. Figure 8 illustrates the backup mode alarm timing.
Figure 7.
Alarm interrupt reset waveform
Table 6.
Alarm repeat modes
RPT4
RPT3
RPT2
RPT1
Alarm activated
1
Once per second
1
0
Once per minute
1
0
Once per hour
1
0
Once per day
0
Once per month
AI01677B
A0-A14
ACTIVE FLAG BIT
ADDRESS 7FF0h
IRQ/FT
15ns Min
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711KA2VFS2 | 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQFP64 |
| MC68HC711KA2VFS3 | 8-BIT, UVPROM, 3 MHz, MICROCONTROLLER, CQFP64 |
| M37700SAFP | 16-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| MPC603FIM233C | 32-BIT, 233 MHz, RISC PROCESSOR, CPGA288 |
| MPC603VIP266C | 32-BIT, 266 MHz, RISC PROCESSOR, CPGA288 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M48T37V-10MH6 | 功能描述:实时时钟 256K (32Kx8) 100ns RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T37V-10MH6E | 功能描述:实时时钟 256K (32Kx8) 100ns RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T37V-10MH6F | 功能描述:实时时钟 256K (32Kx8) 100ns RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T37V-10MH6TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V 256 Kbit 32Kb x8 TIMEKEEPER SRAM |
| M48T37V-70MH1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V 256 Kbit 32Kb x8 TIMEKEEPER SRAM |
发布紧急采购，3分钟左右您将得到回复。