- 您现在的位置：买卖IC网 > PDF目录69017 > M48T512V-85PM1 (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDIP32 PDF资料下载
参数资料
| 型号： | M48T512V-85PM1 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDIP32 |
| 封装： | ROHS COMPLIANT, PLASTIC, DIP-32 |
| 文件页数： | 3/23页 |
| 文件大小： | 370K |
| 代理商： | M48T512V-85PM1 |
M48T512Y, M48T512V
Clock operations
Doc ID 5747 Rev 6
3
Clock operations
3.1
Reading the clock
Updates to the TIMEKEEPER registers should be halted before clock data is read to
prevent reading data in transition (see Table 5 on page 12). The BiPORT TIMEKEEPER
cells in the RAM array are only data registers and not the actual clock counters, so updating
the registers can be halted without disturbing the clock itself.
Updating is halted when a '1' is written to the READ bit, D6 in the control register (7FFF8h).
As long as a '1' remains in that position, updating is halted. After a halt is issued, the
registers reflect the count; that is, the day, date, and time that were current at the moment
the halt command was issued. All of the TIMEKEEPER registers are updated
simultaneously. A halt will not interrupt an update in progress. The next update occurs 1
second after the READ bit is reset to a '0.'
3.2
Setting the clock
Bit D7 of the control register (7FFF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like
the READ bit, halts updates to the TIMEKEEPER registers. The user can then load them
with the correct day, date, and time data in 24 hour BCD format (see Table 5 on page 12).
Resetting the WRITE bit to a '0' then transfers the values of all time registers 7FFFFh-
7FFF9h to the actual TIMEKEEPER counters and allows normal operation to resume. After
the WRITE bit is reset, the next clock update will occur approximately one second later.
Note:
Upon power-up, both the WRITE bit and the READ bit will be reset to '0.'
3.3
Stopping and starting the oscillator.
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The STOP bit is located at bit D7 within 7FFF9h. Setting it to a '1' stops the
oscillator. The M48T512Y/V is shipped from STMicroelectronics with the STOP bit set to a
'1.' When reset to a '0,' the M48T512Y/V oscillator starts after approximately one second.
Note:
It is not necessary to set the WRITE bit when setting or resetting the FREQUENCY TEST
bit (FT) or the STOP bit (ST).
相关PDF资料 |
PDF描述 |
|---|---|
| M48T512V-70PM1 | REAL TIME CLOCK, PDIP32 |
| M48T513V-85PL1 | 0 TIMER(S), REAL TIME CLOCK, DMA36 |
| M48T513Y-70PM1 | 0 TIMER(S), REAL TIME CLOCK, PDIP36 |
| M48T513V-85PM1 | 0 TIMER(S), REAL TIME CLOCK, PDIP36 |
| M62320GP | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M48T512VPM | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V 4 Mbit 512Kb x8 TIMEKEEPER SRAM |
| M48T512Y | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V 4 Mbit 512Kb x8 TIMEKEEPER SRAM |
| M48T512Y_10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5.0 or 3.3 V, 4 Mbit (512 Kbit x 8) TIMEKEEPER? SRAM |
| M48T512Y-70PM1 | 功能描述:实时时钟 4M (512Kx8) 70ns RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T512Y-70PM1 | 制造商:STMicroelectronics 功能描述:NVRAM 10 YR BATTERY 4MB 48T512 |
发布紧急采购，3分钟左右您将得到回复。