- 您现在的位置：买卖IC网 > PDF目录45052 > M48T86MH1E (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO28 PDF资料下载
参数资料
| 型号： | M48T86MH1E |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| 封装： | 0.330 INCH, ROHS COMPLIANT, PLASTIC, SOH-28 |
| 文件页数： | 9/36页 |
| 文件大小： | 352K |
| 代理商： | M48T86MH1E |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Obsolete
Product(s)
- Obsolete
Product(s)
M48T86
Clock operations
3.5
Alarm interrupt
The alarm interrupt provides the system processor with an interrupt when a match is made
between the RTC's hours, minutes, and seconds bytes and the corresponding alarm bytes.
The three alarm bytes can be used in two ways. First, when the alarm time is written in the
appropriate hours, minutes, and seconds alarm locations, the alarm interrupt is initiated at
the specified time each day if the Alarm Interrupt Enable bit (Register B; Bit 5) is high. The
second use is to insert a “Don't care” state in one or more of the three alarm bytes. The
“Don't care” code is any hexadecimal value from C0 to FF. The two most significant bits of
each byte set the “Don't care” condition when at logic '1.' An alarm will be generated each
hour when the “Don't care” is are set in the hours byte. Similarly, an alarm is generated
every minute with “Don't care” codes in the hour and minute alarm bytes. The “Don't care”
codes in all three alarm bytes create an interrupt every second.
3.6
Update cycle interrupt
After each update cycle, the Update Cycle Ended Flag bit (UF) (Register C; Bit 4) is set to a
'1.' If the Update Interrupt Enable bit (UIE) (Register B; Bit 4) is set to a '1,' and the SET bit
(Register B; Bit 7) is a '0,' then an interrupt request is generated at the end of each update
cycle.
3.7
Oscillator control bits
When the M48T86 is shipped from the factory the internal oscillator is turned off. This
feature prevents the lithium energy cell from being discharged until it is installed in a system.
A pattern of “010” in Bits 4-6 of Register A will turn the oscillator on and enable the
countdown chain. A pattern of “11X” will turn the oscillator on, but holds the countdown
chain of the oscillator in reset. All other combinations of Bits 4-6 keep the oscillator off.
3.8
Update cycle
The M48T86 executes an update cycle once per second regardless of the SET bit (Register
B; Bit 7). When the SET bit is asserted, the user copy of the double buffered time, calendar,
and alarm bytes is frozen and will not update as the time increments. However, the time
countdown chain continues to update the internal copy of the buffer. This feature allows
accurate time to be maintained, independent of reading and writing the time, calendar, and
alarm buffers. This also guarantees that the time and calendar information will be
consistent. The update cycle also compares each alarm byte with the corresponding time
byte and issues an alarm if a match or if a “Don't care” code is present in all three positions.
There are three methods of accessing the real time clock that will avoid any possibility of
obtaining inconsistent time and calendar data. The first method uses the update-ended
interrupt. If enabled, an interrupt occurs after every update cycle which indicates that over
999ms are available to read valid time and date information. If this interrupt is used, the
IRQF Bit (Register C; Bit 7) should be cleared before leaving the interrupt routine.
A second method uses the Update-In-Progress (UIP) bit (Register A; Bit 7) to determine if
the update cycle is in progress. The UIP bit will pulse once per second. After the UIP bit
goes high, the update transfer occurs 244 s later. If a low is read on the UIP bit, the user
has at least 244 s before the time/calendar data will be changed. Therefore, the user
相关PDF资料 |
PDF描述 |
|---|---|
| M4T32-BR12SH1 | 1 TIMER(S), REAL TIME CLOCK, DSS4 |
| M50734FP-10 | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP72 |
| M50734SP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
| M50930-XXXFP | 8-BIT, MROM, 4.3 MHz, MICROCONTROLLER, PQFP80 |
| M50931-XXXFP | 8-BIT, MROM, 4.3 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M48T86MH1F | 功能描述:实时时钟 5 Volt PC Drop-In RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T86MH1TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5.0 V PC real-time clock |
| M48T86PC | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V PC REAL TIME CLOCK |
| M48T86PC1 | 功能描述:实时时钟 5 Volt PC Drop-In RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M48T86PC1 | 制造商:STMicroelectronics 功能描述:IC - Real Time Clock |
发布紧急采购，3分钟左右您将得到回复。