- 您现在的位置：买卖IC网 > PDF目录379298 > M68HC11K (Motorola, Inc.) 8-BIT MICROCONTROLLER PDF资料下载
参数资料
| 型号： | M68HC11K |
| 厂商： | Motorola, Inc. |
| 元件分类： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件页数： | 19/80页 |
| 文件大小： | 420K |
| 代理商： | M68HC11K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
M68HC11 K Series
MC6HC11KTS/D
MOTOROLA
19
6.
Clear the EPROG register to reconfigure the EPROM address and data buses for normal op-
eration.
In EPROM emulation mode (PROG mode), the EPROM/OTPROM is programmed as a stand-alone
EPROM by adapting the MCU footprint to the 27C256-type EPROM and using an appropriate EPROM
programmer. To put the MCU in PROG mode, pull the following pins low: MODA/LIR, MODB/V
STBY
,
RESET, PA[2:0]. Refer to
Figure 6
.
In the third method, the EPROM is programmed by software while in the special test or bootstrap
modes. User-developed software can be uploaded through the SCI, or a ROM resident EPROM pro-
gramming utility can be used. To use the resident utility, bootload a three-byte program consisting of a
single jump instruction to $BF00. $BF00 is the starting address of a resident EPROM programming util-
ity. The utility program sets the X and Y index registers to default values, then receives programming
data from an external host and programs it into EPROM. The value in IX determines programming delay
time. The value in IY is a pointer to the first address in EPROM to be programmed (default = $A000).
When the utility program is ready to receive programming data, it sends the host the $FF character.
Then it waits. When the host sees the $FF character, the EPROM programming data is sent, starting
with the first location in the EPROM array. After the last byte to be programmed is sent and the corre-
sponding verification data is returned, the programming operation is terminated by resetting the MCU.
Although the external 12.25 V programming voltage must be applied to the XIRQ/V
PPE
pin during
EPROM programming, it should be equal to V
DD
before verifying the data that was just programmed. It
should equal V
DD
during normal operation also. The XIRQ/V
PPE
pin has a high voltage detect circuit
that inhibits assertion of the ELAT bit when programming voltage is at low levels.
CAUTION
If the MCU is used in any operating mode while high voltage (12.25 V nominal) is
present on the XIRQ/V
PPE
pin, the IRQ/CE pin must be pulled high to avoid acci-
dental programming or corruption of EPROM contents. After programming an
EPROM location, IRQ pin must also be pulled high before the address and data
are changed to program the next location.
MBE —Multiple-Byte Programming Enable
0 = EPROM array configured for normal programming
1 = Program two bytes with the same data
When multiple-byte programming is enabled, address bit 5 is considered a don't care so that bytes with
address bit 5 = 0 and address bit 5 = 1 both get programmed. MBE can be read in any mode and always
reads zero in normal modes. MBE can only be written in special modes.
Bit 6 —Not implemented
Always reads zero
ELAT —EPROM Latch Control
ELAT can be read any time. ELAT can be written any time except when EPGM = 1, then the write to
ELAT will be disabled. When ELAT = 1, writes to EPROM cause address and data to be latched and
the EPROM cannot be read.
0 = EPROM address and data bus configured for normal reads
1 = EPROM address and data bus configured for programming
EPROG
—
EPROM Programming Control
$002B
Bit 7
6
5
4
3
2
1
Bit 0
MBE
—
ELAT
EXCOL
EXROW
—
—
EPGM
RESET:
0
0
0
0
0
0
0
0
相关PDF资料 |
PDF描述 |
|---|---|
| M68HC711CFD | CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68HC711CFG | CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68SDIL12 | The MC68HC912DT128A microcontroller unit (MCU) is a 16-bit device composed of standard on-chip peripherals including a 16-bit central processing unit |
| M68ADP912DG128PV | The MC68HC912DT128A microcontroller unit (MCU) is a 16-bit device composed of standard on-chip peripherals including a 16-bit central processing unit |
| MAC218A10 | TRIACs 8 AMPERES RMS 200 thru 800 VOLTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M68HC11K_1 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontroller |
| M68HC11K_13 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC11K Family Technical Data |
| M68HC11K0 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:CONFIG Register Programming for EEPROM-based M68HC11 Microcontrollers |
| M68HC11K1 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:CONFIG Register Programming for EEPROM-based M68HC11 Microcontrollers |
| M68HC11K2 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:CONFIG Register Programming for EEPROM-based M68HC11 Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。