- 您现在的位置：买卖IC网 > PDF目录45052 > M6XXLFXI (CYPRESS SEMICONDUCTOR CORP) OTHER CLOCK GENERATOR, QCC16 PDF资料下载
参数资料
| 型号： | M6XXLFXI |
| 厂商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | OTHER CLOCK GENERATOR, QCC16 |
| 封装： | 3 X 3 MM, LEAD FREE, MO-220, QFN-24 |
| 文件页数： | 14/17页 |
| 文件大小： | 475K |
| 代理商： | M6XXLFXI |
MoBL Clock
M300/M600
Document Number: 001-12946 Rev. *C
Page 6 of 17
I2C Serial Interface
To enhance the flexibility and function of the clock synthesizer, a
two-signal I2C serial interface is provided. This interface is used
to write (and optionally read) control registers that control various
device functions such as enabling individual clock output buffers.
The registers initialize to their default setting upon power up and
therefore, use of this interface is optional. Clock device registers
are normally changed upon system initialization. Any data written
via I2C is volatile and is not retained when the device is powered
down.
The I2C interface uses two signals, SDA and SCL, that operates
up to 400 kbits/s in Read or Write mode. The SDA and SCL
timing and data transfer sequence is shown in
Figure 3 on page 7. The basic Write serial format is as follows:
Start Bit; 7-bit Device Address (DA); R/W Bit; Slave Clock
Acknowledge (ACK); 8-bit Memory Address (MA); ACK; 8-bit
Data; ACK; 8-bit Data in MA+1 if desired; ACK; 8-bit Data in
MA+2; ACK; etc. until STOP Bit. The basic serial format is
illustrated in Figure 4 on page 7.
Device Address
The device serial interface address is 69H. The device address
is combined with a read/write bit as the LSB and is sent after
each start bit.
Data Valid
Data is valid when the clock is HIGH, and can only be
transitioned when the clock is LOW, as illustrated in Figure 5 on
Data Frame
Every new data frame is indicated by a start and stop sequence,
as illustrated in Figure 6 on page 8.
Start Sequence – SDA going LOW when SCL is HIGH indicates
a Start Frame. Every time a start signal is supplied, the next 8-bit
data must be the device address (seven bits) and a R/W bit,
followed by register address (eight bits) and register data (eight
bits).
Stop Sequence – SDA going HIGH when SCL is HIGH indicates
a Stop Frame. A Stop Frame frees the bus to write to another part
on the same bus or to write to another random register address.
Acknowledge Pulse
During Write Mode, the MoBL Clock M300/M600 responds with
an Acknowledge pulse after every eight bits. This is done by
pulling the SDA line LOW during the N*9th clock cycle, as
illustrated in Figure 7 on page 8 (N = the number of bytes
transmitted). During Read Mode, the master generates the
acknowledge pulse after reading the data packet.
Write Operations
Writing Individual Bytes
A valid write operation must have a full 8-bit register address
after the device address word from the master, which is followed
by an acknowledge bit from the slave (ack = 0/LOW). The next
eight bits must contain the data word intended for storage. After
the receiving the data word, the slave responds with another
acknowledge bit (ack = 0/LOW), and the master must end the
write sequence with a STOP condition.
Writing Multiple Bytes
To write multiple bytes at a time, the master must not end the
write sequence with a STOP condition, but instead sends
multiple contiguous bytes of data to be stored. After each byte,
the slave responds with an acknowledge bit, the same as after
the first byte, and accepts data until the acknowledge bit is
responded to by the STOP condition. When receiving multiple
bytes, the MoBL Clock M300/M600 internally increments the
register address.
Read Operations
Read operations are initiated the same way as Write operations
except that the R/W bit of the slave address is set to ‘1’ (HIGH).
There are three basic read operations: current address read,
random read, and sequential read.
Current Address Read
The MoBL Clock M300/M600 have an onboard address counter
that retains ‘1’ more than the address of the last word accessed.
If the last word written or read was word ‘n’, then a current
address read operation returns the value stored in location ‘n+1’.
When the MoBL Clock M300/M600 receives the slave address
with the R/W bit set to a ‘1’, it issues an acknowledge and
transmits the 8-bit word. The master device does not
acknowledge the transfer, but generates a STOP condition,
which causes the MoBL Clock M300/M600 to stop transmission.
Random Read
Through random read operations, the master may access any
memory location. To perform this type of read operation, first set
the word address. To do this, send the address to the MoBL
Clock M300/M600 as part of a write operation. After the word
address is sent, the master generates a START condition
following the acknowledge. This terminates the write operation
before any data is stored in the address, but not before the
internal address pointer is set. Next, the master reissues the
control byte with the R/W byte set to ‘1’. The MoBL Clock
M300/M600 then issues an acknowledge and transmits the 8-bit
word. The master device does not acknowledge the transfer, but
generates a STOP condition, which causes the MoBL Clock
M300/M600 to stop transmission.
Sequential Read
Sequential read operations follow the same process as random
reads except that the master issues an acknowledge instead of
a STOP condition after transmission of the first 8-bit data word.
This action increments the internal address pointer, and
subsequently outputs the next 8-bit data word. By continuing to
issue acknowledges instead of STOP conditions, the master
serially reads the entire contents of the slave device memory.
When the internal address pointer points to the FFH register,
after the next increment, the pointer points to the 00H register.
相关PDF资料 |
PDF描述 |
|---|---|
| M300LFXIT | 50 MHz, OTHER CLOCK GENERATOR, QCC16 |
| M74HC00C1R | HC/UH SERIES, QUAD 2-INPUT NAND GATE, PQCC20 |
| M74HC157B1N | HC/UH SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDIP16 |
| M74HC158C1 | HC/UH SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, INVERTED OUTPUT, PQCC20 |
| M74HCT164B1R | HCT SERIES, 8-BIT RIGHT SERIAL IN PARALLEL OUT SHIFT REGISTER, TRUE OUTPUT, PDIP14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M-7 | 功能描述:TERM BARRIER 7 TERM DUAL ROW RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:M 标准包装:1 系列:43000 端接块类型:阻隔块 电路数:27 导线入口数目:27 间距:0.438"（11.12mm） 行数:1 电流:20A 电压:600V 线规:12-22 AWG 顶部端子:螺钉 底部端子:闭合式 阻挡层类型:双壁（双） 特点:- 颜色:- 包装:散装 安装类型:底座安装或面板安装 工作温度:105°C 材料 - 绝缘体:聚丙烯（PP） 材料可燃性额定值:UL94 V-0 |
| M-7.5-400-.010UF | 制造商:Siemens 功能描述: |
| M7/76A/115 | 制造商:PEPPERL+FUCHS 功能描述:PHOTOELECTRIC SENSOR, Sensing Range Max:3.5m, Output Current:100mA, Sensor Outpu |
| M7/76A/143 | 制造商:PEPPERL+FUCHS 功能描述:Sensor, Photoelectric, Thru Beam, 134394 制造商:PEPPERL+FUCHS 功能描述:Photoelectric (Automation) |
| M7/MV7/59/76a/102/115 | 制造商:PEPPERL+FUCHS 功能描述:Mini thru beam sensor, pre-wired NPN |
发布紧急采购，3分钟左右您将得到回复。